Competent tuning of the VAZ 2107 interior
Tips for motorists

Competent tuning of the VAZ 2107 interior

03.03.2023 /

Although the VAZ 2107 has recently appeared less and less on our roads, these are quite popular cars that are still in demand. Unfortunately, it cannot be said that the interior of the "seven" meets modern standards of safety and comfort. This encourages owners of these cars to modernize the interior, improving performance, design and ergonomics.

Salon VAZ 2107 - description

"Seven" is equipped with a relatively comfortable interior, in comparison with other cars of the classic row of rear-wheel drive VAZs. It has anatomical seats with high backs and headrests, an anti-glare dashboard and electric rear window heating.

The plastic from which the instrument panel and other interior elements are made is not of high quality and has a chemical smell that does not actually disappear, especially on new cars.

Salon is spacious enough. It is illuminated by a ceiling lamp, which is located on the roof of the car and is controlled by a manual switch. In addition, there are door switches that are installed in the door pillars. Note that the interior of the VAZ 2107 has many ergonomic miscalculations. For example, the ignition switch is located to the left of the steering wheel, which is inconvenient for a right-hander. Also, there is no rubber seal around the perimeter of the doors, which is why the doors close with a specific knock.

As for the dashboard, it has a simple design and provides the motorist with only the necessary information, namely: the temperature of the engine and oil, the amount of fuel and revolutions, as well as the current speed of the car. Only the most basic components are located on the center console, in particular: air supply deflectors, heater control unit and cigarette lighter.

A distinctive feature of the VAZ 2107 is the presence of an analog clock. The buttons for activating the headlights, heated rear window and fan are located under the gearshift lever, which is not very familiar. The disadvantages of the “seven” interior also include the fact that the steering wheel is not adjustable at all, and the seats can only be moved along the skid.

Photo gallery: salon VAZ 2107

Competent tuning of the VAZ 2107 interior
Engineers endowed the VAZ 2107 with a four-spoke steering wheel, which is mounted on a polyurethane frame
Competent tuning of the VAZ 2107 interior
Once upon a time, the "classics" were valued for a high-quality interior. Today, alas, even here there is plenty of reason for criticism.
Competent tuning of the VAZ 2107 interior
Salon VAZ 2107 after tuning

Interior trim

A feature of the operation of the salon is that it is exposed not only to external factors (for example, it burns out in the sun), but also to a person. Finishing accumulates odor over time, gets dirty and wears out. Therefore, many car owners decide to reupholster the interior. The modern market is represented by many different materials for sheathing, which is why it is sometimes difficult for car owners to make the right choice. We suggest that you familiarize yourself with the table, which presents the materials that are used for the upholstery of the VAZ 2107 interior.

Table: interior upholstery materials

MaterialAdvantagesDisadvantages
LeatherPractical in operation;

resistant to mechanical stress, temperature and humidity changes;

is a soundproofing material;

improves the acoustic characteristics of the cabin.		Dependence on temperature: in winter, the interior freezes, and in summer it heats up;

leather is expensive

leather interior requires systematic care with the help of special tools.
VeloursSoft, warm and elastic material;

good for dry cleaning;

resistant to damage;

has an acceptable cost.		Wipes off with heavy use

real velor is produced by a limited number of manufacturers, so there is a risk of acquiring a simplified low-quality analogue.
AlcantaraElastic and maintainable;

practical in operation;

easy to clean;

resistant to burning;

soft and comfortable;

does not wear out and does not fade in the sun.		It has no disadvantages, except for the high cost.
DermantinIt is a budget alternative to genuine leather;

leatherette is easy to work with, as it is plastic and flexible.		It is short-lived and easily spoiled as a result of mechanical influences.
AutocarpetStretches well;

has an extensive range of colors;

has excellent thermal insulation properties

does not collect dust and does not fade in the sun.		It doesn't look very attractive.

Seat upholstery

If you have already decided on the material for the upholstery of the seats, think about what color your chairs will be. It is advisable to choose the color of the material for the interior upholstery. The easiest option is to sheathe the seats with a single-color material. However, the combination of several colors will make your salon more original and exclusive.

Competent tuning of the VAZ 2107 interior
Armchair after reupholstering

Seat tightening is done as follows:

  1. We remove the seats from the car.
  2. We remove the regular cover from the chair.
  3. We separate the cover at the seams to transfer to a new material.
  4. We apply each part of the regular cover to the new material and press it with a load. Outline with a marker.
  5. Cut out the details of the new cover with scissors.
  6. Using glue, we strengthen the elements of the cover with foam rubber.
  7. We sew the reinforced elements.
  8. We glue the lapels of the seams, cut off the excess material.
  9. We beat off the seams with a hammer.
  10. We sew the lapels with a double finishing stitch.
  11. We wear seat covers. We start stretching from the back.

Video: seat upholstery VAZ 2107

Padding of the salon VAZ 2107

Door trim

Decorative door panels and plastic elements on the VAZ 2107 are attached using disposable polymer caps. This is technologically advanced and cheap, but not reliable enough, so after a while the panels begin to creak.

You can fix this problem yourself:

  1. First, interior elements are dismantled (handles for opening the lock and power window, armrest, and others). The door trim is removed with a screwdriver.
  2. Next, the door panel is removed and placed on a sheet of plywood 4 mm thick. The outline is outlined with a marker.
  3. The plywood blank is cut with a jigsaw, and the edges are cleaned with sandpaper.
  4. Sheathing is made using a sewing machine.
  5. Foam rubber is glued to the plywood, on top of which the fabric is attached. Don't forget to make holes for interior details. The panel is attached to the door with decorative bolts.

Video: do-it-yourself door cards VAZ 2107

Rear shelf lining

For the upholstery of the rear acoustic shelf, you will first need the right material. The shape of the shelf is uneven with recesses, so it is better to use materials that stretch well. Another important point is the glue. It is advisable to purchase a two-component version - it is his specialized studios that are used when hauling plastic and other interior elements.

Work order:

  1. Remove the rear shelf and take it to a well-ventilated area so that the smell of glue can dissipate faster.
  2. Clean the shelf of dust and dirt for better adhesion.
  3. Apply glue to the material and the shelf. Wait until it dries a little (for each glue, the waiting time is different, it should be indicated on the glue package).
  4. Attach the material and start smoothing from the middle to the edges.
  5. At the last stage, leave the shelf to dry for 24 hours. You can put a load on top to prevent the material from peeling off.

Floor sheathing

Many owners of the "seven" mistakenly believe that linoleum can be put in place of the factory carpet. This is the wrong decision, since linoleum absorbs moisture well, which is why the floor in the "seven" will rot very quickly. However, you can lay linoleum for a while, until you lay carpet, which looks more aesthetically pleasing and has soundproofing characteristics.

You can buy ordinary household carpet. It is better to choose synthetic material with a short pile. For example, polyamide or nylon - it is easy to clean and can last more than ten years. Carpet made of polyester and acrylic is also suitable. They have a hard pile, so they do not actually wear out. If you want a budget option, buy a polypropylene cover.

Instructions for installing carpet in a car:

  1. Remove the seats and remove the old cover.
  2. Before laying the carpet, treat the floor with bituminous or rubber mastic. If there is rust, clean it and treat it with special anti-corrosion agents (for example, LIQUI MOLY).
  3. Make cutouts in the carpet where needed.
  4. Place the carpet carefully on the floor. The cut parts should match the parts.
  5. Dampen the carpet with water and shape it by stretching it.
  6. Remove the material from the interior and leave to dry for a while.
  7. When the carpet is dry, put it back in place.
  8. Secure the material with double-sided adhesive or tape.

Video: salon carpet for the VAZ-classic

Sound insulation of the cabin

A significant drawback of the VAZ 2107 is the increased noise in the cabin when driving. To eliminate it, it is necessary to perform soundproofing of the cabin. This is a somewhat costly procedure, although not difficult. Soundproofing materials can be divided into three groups: heat insulators, sound insulators and vibration dampers, but on the modern market there are universal tools that combine all the properties.

Note that for ease of installation, virtually all materials are made on a self-adhesive basis. Some of them need to be heated with a hair dryer during installation. Vibration isolation material (vibroplast) is laid first, which dampens vibrations of the body, engine and suspension. Next comes the sound-absorbing layer (bitoplast), which prevents extraneous sounds from entering the cabin. In order not to be divided into two layers, you can take a universal material.

In addition to soundproofing materials, you will need:

Soundproofing underbody and wheel arches

For external processing of the bottom and wheel arches, do the following:

  1. Wash the car thoroughly, especially the parts to be treated.
  2. Let the car dry, blow out the cavities with air flow.
  3. Prepare the surface by degreasing it with special solvents, such as white spirit.
  4. Apply soundproofing to the desired surfaces of the car using a spray gun or a paint brush.
  5. Do not leave gaps, the mastic layer should be uniform.
  6. Install fender lockers in the wheel arches and secure them with self-tapping screws.

Soundproofing doors

Soundproofing of doors is carried out in order to get rid of external noise and improve the sound quality of the acoustic system. This process is quite painstaking and requires the dismantling of door trim and interior elements.

The soundproofing kit includes only damping material, however, surface treatment with sound absorbers will not be superfluous.

  1. After dismantling the door upholstery and interior parts, treat the surface with a degreaser.
  2. The first layer must be applied vibration isolation. The material is glued to the inside of the door through special technological holes. Vibroplast Silver proved itself well here. You need to glue the material tightly, without missing a single millimeter.

    As a rule, anticorrosive is applied to the car door. Remove it, otherwise the vibroplast will not stick. Before sticking the material, adjust all locks and rods to avoid rattling.

  3. Next, we glue the bitoplast, its thickness should be four millimeters.
  4. Then you need to glue the outer part of the door under the cards. This is great for audiophiles. Fully seal the access holes to seal the part of the door where the speaker is located.
  5. Processing with a vibration filter will make it possible to increase the rigidity of the door, which has a good effect on the sound of acoustics.
  6. Paste the outer sides with a visomat, and then with Splen.
  7. After gluing, heat the vibroplast with a hairdryer, smoothing the material with a roller or palms.

Video: soundproofing door cards

Soundproofing the engine compartment

The engine is one of the main sources of noise in a car. The order of work is as follows:

  1. First of all, clean the inside of the hood from dirt and dust.
  2. Next, degrease the surface with solvents.
  3. Attach a sheet of finished soundproofing to the hood and cut along the contour.
  4. If you purchased self-adhesive material, simply stick it on the desired surface, after removing the protective film.
  5. Be sure to stick on a layer of foil to improve heat reflection, protect the soundproofing layer, and increase the engine's warm-up rate in winter.

More about soundproofing VAZ-2107: https://bumper.guru/klassicheskie-modeli-vaz/salon/shumoizolyatsiya-vaz-2107.html

Front Panel

Console tuning is its optimization, the result of which will be the appearance in the car of a number of advantages and useful little things. The purpose of this upgrade is to make the front panel more functional and original. You can replace the torpedo with a similar one from the VAZ-2115. But be prepared for the fact that during installation there may be a problem with gaps that need to be sealed with mounting foam.

On the "seven" you can also install the front panel from a foreign car. The best option is the dashboard with the BMW E30. In addition, an analogue from TOYOTA Camry is often used. In this case, cut the element a little on the sides, install power windows and correctly select the casing on the steering wheel. As an option, you can sheathe a standard torpedo with carbon fiber or fabric, which will give it a bright and original appearance.

Dashboard

The car interior is equipped with a dashboard for the driver to track the parameters of movement, the health of the main units and detect emergency breakdowns. All the main elements on the instrument panel are placed under the protective glass.

Possible ways to refine the instrument panel VAZ 2107:

Learn more about replacing the VAZ-2107 torpedo: https://bumper.guru/klassicheskie-modeli-vaz/elektrooborudovanie/panel-priborov/panel-priborov-vaz-2107.html

Photo gallery: modernization of the dashboard VAZ 2107

Glove box

The glove compartment is one of the weak points of the VAZ 2107 cabin. Unlike previous VAZ models, the glove box on the seven opens down. And when the car is in operation for a long time, the glove compartment often spontaneously opens on pits and bumps. The reason for this is the loose hinges and fastening of the lock. If nothing is done, over time it will not close at all. Not to mention the rattling when driving, which distracts the driver's attention and annoys him.

To fix the problem, many car owners try to bend the lock tab on the cover, which does not give a positive result. In fact, it is necessary to bend the tongue on the panel. If it doesn't help, stick sponge rubber along the length of the lid, which will provide easy springing of the lid during closing. If the hinges are so worn out that the proposed methods do not help, try fixing with furniture or other small-sized magnets.

Glove compartment lighting

The lighting of the glove box on the VAZ 2107 also leaves much to be desired: it is poorly implemented, does not actually shine and rarely functions correctly.

Installing an LED strip is the easiest option for finalizing glove box lighting. It is advisable to give preference to an insulated tape, since the light-emitting elements in it are protected from damage using a special composition. The optimal length of the LED strip is 10-15 centimeters. It is advisable to mount it at the top of the glove box so that the light is directed inside the glove box.

Sitting

And although the seats of the "seven" are considered the most valuable of the entire VAZ family (classic), they have a significant disadvantage - the front seats are flimsy and break pretty quickly. Over time, the back of the driver's seat begins to warp, and even if it is welded, this will not be enough for a long time. In addition, the upholstery on the seat is wiped off, which looks unattractive.

The easiest way to improve the chairs is to purchase covers, but if the seats are very loose, you can replace them with new stock, "foreign", sports or anatomical ones.

Which seats are suitable for VAZ 2107

In addition to stock factory seats, seats from foreign cars can be installed on the VAZ 2107. For example, analogues from the 210 Mercedes W1996 and the 1993 Toyota Corolla are perfect for this purpose. They are easily attached to the regular bolts of the "seven".

Armchairs from Fiat or SKODA are also a good option. But in this case, you will have to make two additional holes for a more secure fit. Elements from Nissan and Peugeot can also be used, but you will encounter certain inconsistencies during installation. Seats from Volkswagen are well suited to the "seven" without any modifications. They are comfortable, but too high, so it is better to refuse this option.

Video: replacing seats on a VAZ from Ford Mondeo

How to remove the head restraints and shorten the seat back

You can shorten the seat back by trimming it. To do this, the chair must be dismantled and disassembled. With the help of a grinder, a part of the frame is sawn off. Such work is very time-consuming, so it is better to turn to specialists. As for the VAZ 2107 head restraints, it is very easy to remove them, for this you just need to pull it up to the stop and press the lock.

Seat belts

Seat belts (hereinafter referred to as RB) require replacement if they are worn out or the locking device is faulty. Also, the RB must be replaced if they experienced a load during the accident. The VAZ 2107 has seat belts with inertial coils. To replace the front seat RB, do the following:

  1. Remove the decorative trims of the lower and upper mountings of the RB to the central pillar by prying them with a screwdriver.
    Competent tuning of the VAZ 2107 interior
    Removing decorative trims for seat belt anchors
  2. Using the key on "17", unscrew the bolt of the upper fastening of the RB.
    Competent tuning of the VAZ 2107 interior
    Unscrewing the bolt of the upper fastening of the seat belt
  3. Using the same wrench, unscrew the lower mounting bolt and dismantle the belt with the coil.
    Competent tuning of the VAZ 2107 interior
    Removing the seat belt with reel
  4. Next, unscrew the fixing bolt of the RB retainer to the floor tunnel and remove it.
    Competent tuning of the VAZ 2107 interior
    Loosening the seat belt anchor bolt
  5. Installing a new belt is done in reverse order.

Interior lighting

Refinement of regular lighting will increase comfort in the cabin and embellish it. You can take the ceiling from Priora, as it has the required characteristics and looks impressive. From the materials you will need: masking tape, a sharp knife, a marker, a “12” key and a screwdriver. First you need to remove the front roof visor. With a marker, outline the installation location of the new ceiling. Cut the visor along this contour. Then you need to attach the ceiling, and fill the seams with sealant.

As for the power connection, it is desirable to conduct new wiring along the right rack. The minus is connected to the body, and the plus is connected to the contact of the ceiling. It is better to make wire conclusions in the area of ​​\uXNUMXb\uXNUMXbthe glove box.

Modification of the stove VAZ 2107

As you know, the efficiency of the VAZ 2107 heater is extremely low, which causes dissatisfaction among the owners of the "seven". To solve this problem, the modernization of the stove will help. There is no need to improve the heater core, as it gives off the optimal amount of heat. This means that in order to increase the efficiency of the stove, it is necessary to improve the blowing system.

The simplest tuning, which does not require virtually any design changes, is to replace the standard fan motor with the one used in the VAZ 2108-2109. This motor has more power and higher RPM. To install it, you need to slightly modify the body of the stove.

Read about the device of the VAZ-2107 stove: https://bumper.guru/klassicheskie-modeli-vaz/sistema-ohdazhdeniya/radiator-pechki-vaz-2107.html

Replacing the regular stove tap will also not be superfluous. The crane is located in the cabin of the "seven" in the area of ​​\uXNUMXb\uXNUMXbthe passenger's legs. Sometimes car owners find out about it only when the coolant (coolant) leaks, which causes a lot of trouble. Replacing the faucet with a similar new product solves the problem only for a while. Therefore, experts recommend replacing it with a curved sealed tube. This will stop the leaks, but you won't be able to cut off the coolant supply to the radiator. Because of this, the cabin will be very hot in the summer.

Alternatively, you can install a conventional water tap to supply coolant to the heater radiator in the engine compartment. The only inconvenience of such tuning is the need to open the hood in order to manipulate the crane.

Video: finalization of the VAZ 2107 stove

Of course, it will take a lot of effort and free time to transform the interior of the "seven", but a competent approach to business and a desire to improve your car will allow you to perform spectacular tuning that will become your pride.

Add a comment