Turn signals: use, maintenance and price
Uncategorized

Turn signals: use, maintenance and price

Almost 55% of French drivers say they forget to systematically activate their indicators when needed. However, indicators play an important role in ensuring safety: they signal any change in the direction of the vehicle.

?? When to use turn signals?

Turn signals: use, maintenance and price

. blinkers have a role to warn other motorists that your vehicle is change of direction... Thus, the direction indicators have two directions: left and right.

Therefore, indicators need to be activated in several situations:

  • For overtaking or drawdown;
  • For lane change ;
  • For Turn ;
  • For insert ;
  • For turn around ;
  • For parking ;
  • For carousel.

Attention : if you forget to turn on the flashing light in one of the above situations, you run the risk of a 2nd class penalty, which will result in 3 points being deducted and € 35 paid (an increase of € 75).

🚗 What are the frequent breakdowns of turn signals?

Turn signals: use, maintenance and price

There are several recurring indicator failures that can alert you to a problem with your car headlights:

  • The turn signals are blinking fast : The flashing frequency may change if one of the direction indicator lamps is burnt out. Therefore, check that each bulb is working correctly. If they are all working properly, this is undoubtedly due to a grounding problem (connection to the chassis).
  • Le stop signal flashing with turn signals : The problem is most likely due to poor contact.
  • Only one of your turn signals no longer works : The indicator light is probably burnt out or defective.
  • Two lights on one side no longer light up : It is definitely the fuse problem that is causing this failure.
  • Turn signals no longer blink : If your turn signals keep on illuminating when activated, this is definitely due to a flashing light problem.
  • Turn signals are no longer activated : The problem may be with the control switch that is used to turn on the turn signals.

🔧 How to change the flasher block?

Turn signals: use, maintenance and price

The flasher unit, also called the flasher relay, is the unit that cuts off the current supplied to the turn signal lamps to cause the flasher to flash. In this guide, you will learn how to replace your car's flasher yourself.

Required material:

  • Protective glasses
  • Protective gloves
  • Tools

Step 1: disconnect the battery

Turn signals: use, maintenance and price

Open the hood and start by disconnecting one of the battery terminals to avoid electric shock while operating the vehicle.

Step 2. Locate the flasher module.

Turn signals: use, maintenance and price

Locate your flashing lights on your vehicle. Its location can vary from one car model to another, but it is often found under the steering wheel or under the hood.

Feel free to consult your vehicle's technical review if you have any doubts about its position. Use a screwdriver to remove the covers required to access the flashing unit.

Step 3: Disconnect the faulty flasher unit

Turn signals: use, maintenance and price

Once the flasher module is located, disconnect the connectors, noting their upstream location.

Feel free to use tape to mark each wire so you know where to reconnect them to the new flashing module. You can also take a picture with your smartphone to see which wire connects to which pin.

Step 4: Install a new firmware module

Turn signals: use, maintenance and price

Make sure that the new flashing light module is identical to the old one (connectors, dimensions, number of pins, etc.). If everything is in order, reconnect the new flasher module, paying particular attention to the location of each connector.

Be sure to connect the wires to the correct connectors on the flasher module. You can then replace the covers that you removed to gain access to the flashing unit.

Step 5: Make sure the turn signals are working correctly

Turn signals: use, maintenance and price

After the new flasher unit and battery are reconnected, take a moment to check that all of your turn signals are working properly.

To do this, turn on the ignition and turn on the direction indicators on one side, then get out of the car to check that the direction indicators are flashing at the front and rear of the vehicle. Remember to check the direction indicators on both sides of the vehicle.

Note : changing the firmware relay is not always necessary if you have problems with the flasher. Indeed, first think about checking that the turn signal bulbs are working properly, because if the bulb is out of order it can affect the rate of flashing.

If the problem persists despite replacing the bulbs, replace the flasher.

?? How much does it cost to replace a turn signal bulb?

Turn signals: use, maintenance and price

The cost of replacing a turn signal bulb varies greatly depending on your car model and the type of bulb. Count on average from 5 to 15 euros for a new indicator bulb. Add working hours to this: count ten euros.

Attention, access to indicators can be more or less difficult from one car model to another and depending on the type of indicator: front indicator, rear indicator, mirror indicator, etc. Therefore, labor cost may vary depending on the model and type of vehicle. ... direction indicator.

If you want your indicators to be serviced in a garage near you, consider comparing the best Vroomly garages for price and customer reviews. Finally, save on the maintenance of your indicators and find the best price online!

Add a comment