car brand | Error code | Error value |
GAS (GAZ) | P0030 | Oxygen sensor (DC) heater circuit malfunction No. 1. External symptom - the MIL lamp does not go out, increased (noticeably) fuel consumption .. 1. Wiring harness or sensor cable is not connected, melted or defective - check the connection from the oxygen sensor to |
GAS (GAZ) | P0031 | Open or short circuit to "Weight" of the oxygen sensor heater circuit No. 1 (see P0030) |
GAS (GAZ) | P0032 | Short circuit to the "Bortset" of the oxygen sensor heater circuit No. 1 (see P0030) |
GAS (GAZ) | P0036 | Malfunction of a chain of a heater of the oxygen sensor No. 2 (see P0030 by analogy) |
GAS (GAZ) | P0037 | Open or short circuit to "Weight" of the oxygen sensor heater circuit No. 2 (see P0030) |
GAS (GAZ) | P0038 | Short circuit to the "Bortset" of the oxygen sensor heater circuit No. 2 (see P0030) |
GAS (GAZ) | P0101 | The signal from the mass air flow sensor (MAF) is out of range: External sign - the MIL lamp does not go out, insufficient engine throttle response, increased fuel consumption, unstable idle .. 1. Deterioration of the MAF parameters - wear or contamination |
GAS (GAZ) | P0102 | Low signal level in the mass air flow sensor circuit (DMRV). An external sign - the MIL lamp does not go out, the engine starts up badly or starts up and stalls, increased engine speed or unstable idle, increased fuel consumption, limits |
GAS (GAZ) | P0103 | High signal level in the mass air flow sensor circuit (MAF) External symptom - the MIL lamp does not go out, the engine does not start well or starts up and stalls, increased engine speed or unstable idle, increased fuel consumption, limits |
GAS (GAZ) | P0105 | Incorrect signal in the air absolute pressure (MAP) sensor circuit. An external symptom - the MIL lamp does not go out, insufficient engine acceleration, increased fuel consumption, unstable idle .. 1. Deterioration of MAP parameters or failure - wear or |
GAS (GAZ) | P0106 | Absolute air pressure sensor signal out of range (see P0105) |
GAS (GAZ) | P0107 | Low signal level in the absolute air pressure (MAP) sensor circuit External symptom - the MIL lamp does not go out, the engine starts poorly or starts up and stalls, increased engine speed or unstable idle, increased fuel consumption, low |
GAS (GAZ) | P0108 | High signal level in the absolute air pressure (MAP) sensor circuit External symptom - the MIL lamp does not go out, the engine starts poorly or starts up and stalls, increased engine speed or unstable idle, increased fuel consumption, ogre |
GAS (GAZ) | P0112 | Low signal level in the intake air temperature sensor (DTV) circuit External symptom - the MIL lamp does not go out, possible detonation of a hot engine, increased fuel consumption, the engine stalls when the car is moving in the cold season at temperatures |
GAS (GAZ) | P0113 | High signal level in the intake air temperature sensor circuit. An external sign - the MIL lamp does not go out, a hot engine detonation is possible, increased fuel consumption. The code can appear in conjunction with others, for example. "Malfunction of the DMRV circuit" and |
GAS (GAZ) | P0115 | Incorrect signal from the coolant temperature sensor (DTOZH) External symptom - the MIL lamp does not go out, increased speed XX, emergency activation of electric fans, increased fuel consumption .. 1. Check the deviation of the DTOZh characteristic from the nominal |
GAS (GAZ) | P0116 | Incorrect coolant temperature sensor signal (see P0115) |
GAS (GAZ) | P0117 | Low signal level in the coolant temperature sensor circuit External symptom - the MIL lamp does not go out, difficult cold start, increased speed of XX, increased fuel consumption .. 1. No fixing of the harness block on the DTOZH - reconnect the block |
GAS (GAZ) | P0118 | High signal level in the coolant temperature sensor circuit External sign - the MIL lamp does not extinguish, difficult cold start, high speed XX, emergency activation of electric fans, increased fuel consumption. |
GAS (GAZ) | P0121 | Incorrect signal in the sensor circuit No. 1 of the throttle position (TPS) External symptom - the MIL lamp does not go out, engine power limitation, increased or floating speed XX and fuel consumption .. 1. Deterioration of TPS parameters - wear of the resistive layer |
GAS (GAZ) | P1551 | Open circuit of the closing circuit (149) of the idle speed controller - see P1509 - for M17.9.7 |
GAS (GAZ) | P1552 | Short circuit to "Mass" of the closing circuit of the regulator XX |
GAS (GAZ) | P1553 | Short circuit to "Bortset" of the closing circuit of the IAC regulator |
GAS (GAZ) | P1558 | Throttle start position out of range. An external symptom is a limitation of engine power, increased or floating speed of XX and fuel consumption. 1. Incorrect initial setting of TPS on the mechanical throttle device. E |
GAS (GAZ) | P1559 | The mass air flow through the throttle is not plausible. An external symptom is a limitation of engine power, increased or floating speed XX and fuel consumption .. 1. Deterioration of the parameters of the mass air flow sensor (MAF) - wear or contamination |
GAS (GAZ) | P1564 | Violation of the adaptation of the choke due to undervoltage. External symptom - difficult starting of the engine, power limitation .. 1. Poor contact between the "ground" of the engine and the body with the terminal "minus" of the battery. - check, clean up the landing |
GAS (GAZ) | P1570 | There is no response from the APS (immobilizer) or communication line failure. External symptom - lamps "MIL" and "IMMO" are on, the engine does not start .. 1. There is no power supply "+ 12V" on the immobilizer unit - check and eliminate .. 2. Break of the K-line of communication between the controller and the unit |
GAS (GAZ) | P1571 | An unregistered electronic key was used. External sign - lamps "MIL" and "IMMO" are on, the engine will not start .. Carry out additional training of the controller with a new set of transponders. You must have 2 trained keys to learn additional |
GAS (GAZ) | P1572 | Open circuit or malfunction of the transceiver antenna of the immobilizer. External sign - "MIL" and "IMMO" lamps are on, the engine will not start .. 1. The antenna of the ignition switch is not connected to the immobilizer unit or open circuit - connect, restore the harness |
GAS (GAZ) | P1573 | Internal malfunction of the APS unit (immobilizer). External symptom - lamps "MIL" and "IMMO" are on, the engine will not start .. 1. Immobilizer malfunction - try to replace the unit. Re-train the controller with this transponder kit |
GAS (GAZ) | P1574 | An attempt to unblock the APS (immobilizer). External symptom - lamps "MIL" and "IMMO" are on, the engine will not start .. 1. There was a multiple attempt to unlock the controller using several different keys or code messages. Further attempts |
GAS (GAZ) | P1575 | Access to engine start is blocked by the controller. An external sign - the "MIL" and "IMMO" lamps are on, the engine does not start .. 1. The controller is blocked after 30-40 starts (for ME17), since only two transponder keys have been trained - conduct training rub |
GAS (GAZ) | P1578 | Invalid results of the throttle valve retraining. External symptom - limitation of engine power, increased or floating speed XX .. 1. Self-adaptation of the initial and final positions of the mechanical throttle valve is performed incorrectly |
GAS (GAZ) | P1579 | Abnormal interruption of throttle adaptation due to external conditions - see P1578. |
GAS (GAZ) | P1600 | No response from immobilizer or communication line fault - see P1570. |
GAS (GAZ) | P1601 | No response from immobilizer or communication line fault - see P1570. |
GAS (GAZ) | P1602 | Loss of voltage of the on-board network at the terminal "30" of the controller. An external symptom - the MIL lamp is on, there may be an unstable idle during the engine warming up process .. The code indicates a complete disconnection of the controller from the vehicle's on-board network (case |
GAS (GAZ) | P1603 | Defective non-volatile memory (EEPROM) of the controller. External symptom - the MIL lamp may light up. 1. Unauthorized modification of the adaptive non-volatile data memory of the controller (EEPROM) using non-standard programming devices - in |
GAS (GAZ) | P1606 | Low or incorrect signal in the Rough Road Sensor (RPC) circuit. An external sign - the MIL lamp is on, the engine power is limited .. 1. There is no fixing of the harness block on the DND - reconnect the block, fix it .. 2. Weakening or oxidation of the contact |
GAS (GAZ) | P1607 | Rough Road Sensor Circuit High - Refer to P1606. |
GAS (GAZ) | P1612 | Unauthorized reset of the controller in working condition. An external sign - the MIL lamp is on, there may be an unstable idle during the engine warming up. The code indicates a short-term disconnection of the controller from the vehicle's on-board network (cl |
GAS (GAZ) | P1616 | Rough Road Sensor Circuit Low or Incorrect - - See P1606. |
GAS (GAZ) | P1617 | Rough Road Sensor Circuit High - Refer to P1606. |
GAS (GAZ) | P1620 | Controller Flash ROM malfunction (checksum error). External symptom - the MIL lamp may light up. Information can be recorded in. "Black box" of the controller - see the section "Service records" of the STM-6 scanner-tester. 1. Unauthorized change |
GAS (GAZ) | P1621 | Controller RAM (random access memory) defective - see P1602. |
GAS (GAZ) | P1622 | Defective non-volatile memory (EEPROM) of the controller. External sign - the MIL lamp may light up. 1. Unauthorized change of passport data, vehicle VIN code, calibration, measurement or adaptation adjustments in the EEPROM controller |
GAS (GAZ) | P1632 | Malfunction of channel No. 1 of the throttle electric drive control. An external sign - the engine does not start, starts up and stalls, increased or decreased idle speed, the engine does not accept the load ("loss of pedal") .. 1. No fixing of the pad harness |
GAS (GAZ) | P1633 | Malfunction of channel No. 2 of the throttle electric drive control. An external sign - the engine does not start, starts up and stalls, increased or decreased idle speed, the engine does not accept the load ("loss of pedal") .. 1. No fixing of the pad harness |
GAS (GAZ) | P1634 | Malfunction of the electric drive of the throttle in the starting position. An external sign - the engine does not start, starts up and stalls, increased or decreased idle speed, the engine does not accept the load (“loss of pedal”) .. 1. Mechanical damage, |
GAS (GAZ) | P1635 | Throttle Actuator Fault in Closed Position - See P1634. |
GAS (GAZ) | P1636 | Motor de-energized malfunction - see P1634. |
GAS (GAZ) | P1640 | Error during the access operation to the EEPROM of the controller - see P1622 |
GAS (GAZ) | P1689 | Invalid error codes in the controller memory. External symptom - the MIL lamp may light up. 1. The controller is faulty - replace it. 2. The type of controller does not correspond to the standard one. Check the marking and passport data of the controller - type, designation, version p |
GAS (GAZ) | P1750 | Short circuit on the "Bortset" circuit No. 1 for controlling the idling torque regulator. External sign - the engine starts up and stalls, or does not start .. 1. There is no fixation of the harness block on the idle speed controller (IAC) - connect the block .. 2. Broken wire in the harness |
GAS (GAZ) | P1751 | Open circuit no. 1 for idle speed control - Refer to P1750. |
GAS (GAZ) | P1752 | Short to Ground of Idle Torque Regulator Control Circuit # 1 - See P1750. |
GAS (GAZ) | P1753 | Short circuit on the "Bortset" of circuit No. 2 for controlling the idle speed controller. - see P1750. |
GAS (GAZ) | P1754 | Open circuit no. 2 for idle speed control - Refer to P1750. |
GAS (GAZ) | P1755 | Short to Ground of Idle Torque Regulator Control Circuit # 2 - See P1750. |
GAS (GAZ) | P2100 | Open in the throttle actuator control circuit - see P1632, P1633. |
GAS (GAZ) | P2102 | Short circuit to "Mass" of the throttle valve electric drive control circuit. - see P1632, P1633. |
GAS (GAZ) | P2103 | Short circuit to the "Bortset" of the throttle valve electric drive control circuit. - see P1632, P1633. |
GAS (GAZ) | P2104 | Idle Throttle Control Limit - See P1634 |
GAS (GAZ) | P2105 | Limiting throttle motor control to engine blocking - see P1634. |
GAS (GAZ) | P2106 | Throttle motor power limitation or circuit malfunction - See P1634. |
GAS (GAZ) | P2110 | Limiting the throttle motor control to the engine speed limit - see P1634. |
GAS (GAZ) | P2111 | Throttle motor control error when throttle is open - see P1634. |
GAS (GAZ) | P2112 | Throttle motor control error when closing throttle - See P1634. |
GAS (GAZ) | P2120 | Acceleration Pedal Position # 1 Sensor Circuit Malfunction - See P2122, P2123. |
GAS (GAZ) | P2122 | Low signal level in the sensor circuit No. 1 of the acceleration pedal position (PU) External symptom - the MIL lamp does not go out, engine power limitation, increased speed XX and increased fuel consumption .. 1. No fixing of the harness block on the PU - reconnect the deck |
GAS (GAZ) | P2123 | High signal level in the acceleration pedal position (PU) sensor circuit No. 1 External symptom - the MIL lamp does not extinguish, engine power limitation, high speed XX and fuel consumption .. 1. Short circuit of the “PU +” and “+3,3” position sensor circuit. XNUMXB "between s |
GAS (GAZ) | P2125 | Acceleration Pedal Position # 1 Sensor Circuit Malfunction - See P2122, P2123. |
GAS (GAZ) | P2127 | Acceleration Pedal Position # 2 Sensor Circuit Low - Refer to P2122. |
GAS (GAZ) | P2128 | Acceleration Pedal Position # 2 Sensor Circuit High - Refer to P2123. |
GAS (GAZ) | P2135 | Discrepancy between the readings of sensors No. 1 and 2 of the throttle position External sign - the MIL lamp does not go out, engine power limitation, increased or floating speed XX and fuel consumption (for E-gas). 1. Deterioration of parameters of one of the sensors by |
GAS (GAZ) | P2138 | Discrepancy between the readings of sensors No. 1 and 2 of the acceleration pedal position (PU) External sign - the MIL lamp does not go out, engine power limitation, increased or floating speed XX and fuel consumption (for E-gas) .. 1. The supply voltage of the PU sensors is different |
GAS (GAZ) | P2173 | High air flow through the throttle when controlling the damper |
GAS (GAZ) | P2175 | Low air flow through the throttle when controlling the damper |
GAS (GAZ) | P2187 | The fuel supply system drifts from "medium" to "poor" area on XX. An external sign is a power failure with repeated load surge at idle speed (XX) or when starting off the car .. 1. A sharp decrease in the vacuum in the intake manifold receiver during a surge |
GAS (GAZ) | P2188 | The fuel supply system drifts from "medium" to "rich" area on XX. An external sign is a power failure due to a repeated load surge at idle speed (XX) or when starting the car. 1. Malfunction of the fuel supply system: increased pressure in |
GAS (GAZ) | P2195 | There is no coincidence of signals from oxygen sensors No. 1 and No. 2. External sign - the MIL lamp does not go out, decreased engine throttle response, increased (noticeably) fuel consumption .. 1. Oxygen sensor No. 1 (DK-1) or No. 2 (DK-2) does not match the standard type or is defective |
GAS (GAZ) | P2270 | No. 2 oxygen sensor signal is in poor condition - see P0171. |
GAS (GAZ) | P2271 | No. 2 oxygen sensor signal is in rich condition - see P0172. |
GAS (GAZ) | P2299 | Inconsistency between brake switch signals and acceleration pedal sensors. External symptom - dips, power limitation, loss of acceleration pedal .. 1. Brake pedal switches not adjusted - adjust (see P0504) .. 2. One or two switches |
GAS (GAZ) | P2301 | Short circuit to the "Bortset" of the primary circuit of the ignition coil 1 (1/4). External sign - one or two cylinders do not work - the engine “doubles” or “troits” .. 1. Short circuit of the harness wires to the ignition coil between themselves or to “+ 12V”. - "ringing |
GAS (GAZ) | P2303 | Short circuit to the "Bortset" of the primary circuit of the ignition coil 2 (2/3) - see 2301. |
GAS (GAZ) | P2304 | Short circuit to the "Bortset" of the primary circuit of the ignition coil 2 (2/3) - see 2301 |
GAS (GAZ) | P2305 | Short circuit to the "Bortset" of the primary circuit of the ignition coil 3 (2/3) - see 2301 |
GAS (GAZ) | P2307 | Short circuit on the "Bortset" of the primary circuit of the ignition coil 3 (2/3) or 4 (1/4) - see 2301 |
GAS (GAZ) | P2310 | Short circuit to the "Bortset" of the primary circuit of the ignition coil 4 (1/4) - see 2301 |
GAS (GAZ) | P3999 | Synchronization error on the signals from the crankshaft position sensor. External sign - the engine does not start ("does not grasp") or starts up poorly, high unevenness of engine idling .. 1. High level of interference from the ignition system |
GAS (GAZ) | P4035 | Left front wheel speed sensor (LF) circuit malfunction. External sign - the “ABS” lamp is on, the ABS system is not functioning. |
GAS (GAZ) | P4040 | Right Front Wheel Speed (RF) Sensor Circuit Malfunction - Refer to P4035. |
GAS (GAZ) | P4045 | Left Rear Wheel Speed (LR) Sensor Circuit Malfunction - Refer to P4035. |
GAS (GAZ) | P4050 | Right Rear Wheel Speed (RR) Sensor Circuit Malfunction - Refer to P4035. |
GAS (GAZ) | P4060 | Malfunction of pump # 1 circuit or left front wheel outlet valve (AV-LF). External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning. Definition condition - the wheel continues to block while the brake pedal is constantly depressed. |
GAS (GAZ) | P4065 | Malfunction of pump # 2 circuit or left front wheel inlet valve. (EV-LF). External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning. Definition condition - the wheel is not braked when the brake pedal is constantly depressed. 1. Not bad |
GAS (GAZ) | P4070 | Malfunction of pump # 1 circuit or right front wheel outlet valve. (AV-RF) - See P4060. |
GAS (GAZ) | P4075 | No. 2 pump circuit or right front wheel inlet valve malfunction. (EV-RF) - see P4065. |
GAS (GAZ) | P4090 | Malfunction of pump # 1 circuit or rear axle outlet valve. (AV-RA) - see P4060 |
GAS (GAZ) | P4095 | No. 2 pump circuit or rear axle inlet valve malfunction. (EV-RA) - see P4065 |
GAS (GAZ) | P4110 | The electric drive (motor) of the pump does not work well or does not stop. External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning. |
GAS (GAZ) | P4121 | Malfunction of the valve power supply circuit. External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning .. 1. One of the power fuses of the ABS system is burnt out - check the serviceability and rating of the fuses, replace if necessary .. 2 |
GAS (GAZ) | P4161 | Brake switch circuit malfunction. External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning. 1. There is no power supply "+ 12V" on the brake pedal switch or open circuit "Stop light". connected with the hydromodulator - "ring" with an ohmmeter, during |
GAS (GAZ) | P4245 | Wheel speed sensor frequency error. External symptom - the "ABS" lamp is on, the ABS system is not functioning.. Condition for determining - the speed of the vehicle wheel exceeds the permissible value. |
GAS (GAZ) | P4287 | Malfunction of the acceleration sensor (DU) circuit. External symptom - the "ABS" lamp is on, the ABS system is not functioning .. Determination condition - the sensor signal does not change during acceleration or deceleration of the vehicle, or its value exceeds the permissible value (10 m / s2 |
GAS (GAZ) | P4550 | Malfunction of the ABS control controller. External symptom - lamps "ABS" and "EBD" are on, the ABS system is not functioning .. 1. Internal malfunction of the controller built into the hydromodulator - replace the hydromodulator according to its type and marking. through |
GAS (GAZ) | P4800 | Low or high voltage of the on-board network. External sign - lamps "ABS" and "EBD" are on, the ABS system is not functioning. The condition for the determination is that the voltage of the on-board network is outside the range of 7,5 ... 16V. 1. Bad contact of the wire "mass-hydromodulator" of the wire harness |
GAS (GAZ) | U0001 | Malfunction of the CAN information bus. External symptom (after start-up) - lamps do not go out: emergency coolant temperature, emergency oil pressure, engine malfunction (MIL); the tachometer and the coolant temperature gauge do not work |
GAS (GAZ) | P0122 | Low signal level in the throttle position sensor No. 1 circuit External sign - the MIL lamp does not go out, engine power limitation, increased speed of XX and fuel consumption .. 1. No fixing of the harness block on the TPS - reconnect the block, |
GAS (GAZ) | P0123 | High signal level in the throttle position sensor circuit No. 1 External symptom - the MIL lamp does not go out, engine power limitation, increased idle speed and fuel consumption. |
GAS (GAZ) | P0130 | Malfunction of the signal circuit or loss of activity of the oxygen sensor No. 1. External sign - the MIL lamp does not go out, increased toxicity and fuel consumption .. 1. No fixing of the harness block on the DC - reconnect the block, fix .. 2. Weakening or oki |
GAS (GAZ) | P0131 | Low signal level in the oxygen sensor (DC) circuit No. 1. External sign - the MIL lamp does not extinguish, increased toxicity and fuel consumption. inspect, replace the DC or about |
GAS (GAZ) | P0132 | High signal level in the oxygen sensor (DC) circuit No. 1. External symptom - the MIL lamp does not go out, increased toxicity and fuel consumption. 1. The signal wires "DK +" and "DK-" in the harness are interchanged - eliminate .. 2. Hit "+ 12V" (from the heater DK) or "+5 |
GAS (GAZ) | P0133 | Slow response to a change in the mixture composition of the oxygen sensor No. 1 (see P0130) |
GAS (GAZ) | P0134 | Loss of signal activity or open circuit of the oxygen sensor No. 1 (see P0130) |
GAS (GAZ) | P0135 | Malfunction of a chain of a heater of the oxygen sensor No. 1 (see P0030) |
GAS (GAZ) | P0136 | Malfunction of the signal circuit of the oxygen sensor No. 2 (see P0130) |
GAS (GAZ) | P0137 | Low signal level in the oxygen sensor circuit No. 2 (see P0131) |
GAS (GAZ) | P0138 | High signal level in the oxygen sensor circuit No. 2 (see P0132) |
GAS (GAZ) | P0140 | Loss of signal activity or open circuit of the oxygen sensor No. 2 (see P0130) |
GAS (GAZ) | P0141 | Malfunction of a chain of a heater of the oxygen sensor No. 2 (see P0030) |
GAS (GAZ) | P0171 | The fuel supply system is too "poor" at its maximum enrichment. External symptom - the code is not immediately identified, the MIL lamp may light up not in the first cycle of engine operation, increased fuel consumption and toxicity. 1. Power system malfunction. |
GAS (GAZ) | P0172 | The fuel supply system is too "rich" at its maximum depletion External symptom - the code is not immediately identified, the MIL lamp may not light up in the first cycle of engine operation, increased fuel consumption and toxicity, decreased engine power, |
GAS (GAZ) | P0200 | One or more injector control circuits are faulty. An external sign - the MIL lamp does not go out, the engine does not start well, after starting one or two cylinders do not work - "troit" or "double" .. 1. There is no fixation of the harness block on the injector or is not connected |
GAS (GAZ) | P0201 | Malfunction or open circuit of the injector 1 control (see P0200) |
GAS (GAZ) | P0202 | Malfunction or open circuit of the injector 2 control (see P0200) |
GAS (GAZ) | P0203 | Malfunction or open circuit of the injector 3 control (see P0200) |
GAS (GAZ) | P0204 | Malfunction or open circuit of the injector 4 control (see P0200) |
GAS (GAZ) | P0217 | Overheating of the engine cooling system. External sign - the MIL lamp and the engine overheat indicator do not go out, one or both electric fans are constantly on, the engine tends to detonate, increased fuel consumption .. 1. "Sticking" of the thermostat - |
GAS (GAZ) | P0219 | Exceeding the permissible engine speed. External symptom - the engine does not develop power or operates in the speed limit mode .. 1. Violation of the requirements for vehicle operation - reduce the engine speed .. 2. Defective |
GAS (GAZ) | P0222 | Low signal level in the sensor circuit No. 2 throttle position. An external sign - the MIL lamp does not go out, a significant limitation of engine power, increased speed of XX and fuel consumption. (for E-gas) .. 1. There is no fixation of the harness block on the throttle |
GAS (GAZ) | P0223 | High signal level in the throttle position sensor No. 2 circuit External sign - the MIL lamp does not extinguish, significant limitation of engine power, increased speed of XX and fuel consumption (for E-gas) .. 1. Short circuit of the sensor circuits "ДПДЗ +" |
GAS (GAZ) | P0230 | Malfunction of the control circuit of the electric fuel pump relay. An external sign - the electric fuel pump (EBN) does not turn on, the engine does not start .. 1. Check the fuses in the mounting block in the passenger compartment, in a special block under the hood, or the fuses installed |
GAS (GAZ) | P0261 | Open or short to ground in injector 1 control circuit - see P0200 |
GAS (GAZ) | P0262 | Short circuit to the "Bortset" injector circuit 1 - see P0200 |
GAS (GAZ) | P0263 | Limiting torque drop in cylinder 1 or malfunction of the injector 1 control driver. External symptom - the MIL lamp does not go out, the engine does not start well, after starting one cylinder does not work - "troit". 1. High or too low resistance |
GAS (GAZ) | P0264 | Open or short to ground in injector 2 control circuit - see P0200 |
GAS (GAZ) | P0265 | Short circuit to the "Bortset" injector circuit 2 - see P0200 |
GAS (GAZ) | P0266 | Cylinder 2 Torque Drop Limit or Injector 2 Control Driver Malfunction - See P0263 |
GAS (GAZ) | P0267 | Open or short to ground in injector 3 control circuit - see P0200 |
GAS (GAZ) | P0268 | Short circuit to the "Bortset" injector circuit 3 - see P0200 |
GAS (GAZ) | P0270 | Open or short to ground in injector 4 control circuit - see P0200 |
GAS (GAZ) | P0271 | Short circuit to the "Bortset" injector circuit 4 - see P0200 |
GAS (GAZ) | P0272 | Cylinder 4 Torque Drop Limit or Injector 4 Control Driver Malfunction - See P0263 |
GAS (GAZ) | P0300 | Misfire detected affecting toxicity. An external sign - the MIL lamp does not go out, the engine does not start well, after starting one or two cylinders do not work - "troit" or "double" .. 1. Ignition misfires in one or two engine cylinders |
GAS (GAZ) | P0301 | Misfire in cylinder 1 (1/4) - see P0300 |
GAS (GAZ) | P0302 | Misfire in cylinder 2 (2/3) - see P0300 |
GAS (GAZ) | P0303 | Misfire in cylinder 3 (2/3) - see P0300 |
GAS (GAZ) | P0304 | Misfire in cylinder 4 (1/4) - see P0300 |
GAS (GAZ) | P0325 | Malfunction or open circuit of the knock sensor. An external sign - the MIL lamp lights up at increased engine speed, engine power drops .. 1. No fixing of the harness block on the sensor - connect the block .. 2. Broken signal wires of the harness - arrange |
GAS (GAZ) | P0327 | Low signal level in the knock sensor circuit - see P0325. |
GAS (GAZ) | P0328 | High signal level in the knock sensor circuit - see P0325. |
GAS (GAZ) | P0335 | Malfunction or open circuit of the crankshaft position sensor (DPKV) External symptom - the engine does not start ("does not grab") or does not start well, the speed is limited to 2500-3000 min-1, high unevenness of the engine rotation at ho |
GAS (GAZ) | P0336 | Synchronization error on the signals from the crankshaft position sensor. An external sign - the engine starts up poorly, high irregularity of the rotational speed, dips during acceleration, detonation. 1. The signal wires of the DPKV + and DPK sensor are mixed up. |
GAS (GAZ) | P0337 | Short to ground in the crankshaft position sensor circuit (see P0335) |
GAS (GAZ) | P0338 | Open circuit of the crankshaft position sensor (see P0335) |
GAS (GAZ) | P0339 | Synchronization error on the signals of the crankshaft position sensor (see P0336) |
GAS (GAZ) | P0340 | Malfunction of the camshaft position sensor (CMP) circuit. External sign - the MIL lamp lights up when the engine is running, increased fuel consumption and toxic emissions .. 1. No fixing of the harness block on the DPRV sensor - connect the block .. 2. О |
GAS (GAZ) | P0341 | Synchronization error on the signals of the camshaft position sensor External symptom - the MIL lamp is on, uneven speed and dips in engine operation, increased fuel consumption and toxic emissions. 1. Damage to the shielding shell |
GAS (GAZ) | P0342 | Low signal level in the camshaft position sensor circuit (P0340) |
GAS (GAZ) | P0343 | High signal in the camshaft position sensor circuit (P0340) |
GAS (GAZ) | P0351 | Open circuit of the primary circuit of the ignition coil 1 (1/4). An external sign - the MIL lamp does not go out, the engine does not start well, after starting one or two cylinders do not work - "troit" or "double" .. 1. There is no fixation of the harness block on the ignition coil - connect the block |
GAS (GAZ) | P0352 | Open circuit of the primary circuit of the ignition coil 2 (2/3) - see P0351 |
GAS (GAZ) | P0353 | Open circuit of the primary circuit of the ignition coil 3 (2/3) - see P0351 |
GAS (GAZ) | P0354 | Open circuit of the primary circuit of the ignition coil 4 (1/4) - see P0351 |
GAS (GAZ) | P0380 | Malfunction of the glow plug relay control circuit. An external symptom - the MIL lamp does not go out, the engine does not start .. 1. Check the fuses of the power circuit of the relay in the mounting block in the passenger compartment or in a special block under the hood .. 2. There is no fixing of the block |
GAS (GAZ) | P0420 | The efficiency of the neutralizer is below the permissible level. An external symptom - the MIL lamp does not go out, reduced engine acceleration, increased fuel consumption .. Code P0420 may be preceded by the appearance of codes: "P0030 ... P0038" ,. "P0130 ... P0141", "P0171, |
GAS (GAZ) | P0422 | The efficiency of the catalytic converter is below the permissible norm - see P0420 |
GAS (GAZ) | P0441 | Incorrect air flow through the purge valve of the adsorber. An external sign - the MIL lamp does not go out, the smell of gasoline under the hood, increased fuel consumption in the summer .. 1. Leakage or jamming of the valve - check the tightness, rinse with salt |
GAS (GAZ) | P0443 | Malfunction of the canister purge valve control circuit. An external sign - the MIL lamp does not go out, the smell of gasoline under the hood, increased fuel consumption in summer .. 1. There is no fixation of the harness block on the valve - connect the block. |
GAS (GAZ) | P0444 | Canister purge valve control circuit malfunction - see P0443 |
GAS (GAZ) | P0445 | Canister purge valve control circuit malfunction - see P0443 |
GAS (GAZ) | P0480 | Malfunction of the control circuit of the relay of the electric fan No. 1. External symptom - the electric cooling fan of the engine (EVO) does not turn on. Turn on / off the EVO relay from the scanner-tester to determine the health of the entire circuit as a whole - if the EVO |
GAS (GAZ) | P0481 | Malfunction of the control circuit of the relay of the electric fan No. 2 - see P0480 |
GAS (GAZ) | P0487 | Open circuit of control of the EGR solenoid valve. An external sign - the MIL lamp does not go out, increased toxicity of exhaust gases .. 1. The recirculation solenoid valve (RRC) is not connected or a wire break in the wiring harness - "ring" ohm |
GAS (GAZ) | P0489 | Short circuit to Bortset of the recirculation valve control circuit - see P0487. |
GAS (GAZ) | P0490 | Short to ground in the recirculation valve control circuit - P0487. |
GAS (GAZ) | P0500 | Circuit malfunction or no signal from the vehicle speed sensor (DSA) External symptom - the MIL lamp lights up when the car is moving, increased fuel consumption, with prolonged operation of the car at high speeds, the neutralizer may be damaged |
GAS (GAZ) | P0501 | Vehicle Speed Sensor Circuit Malfunction - Refer to P0500. |
GAS (GAZ) | P0503 | Intermittent signal from vehicle speed sensor. An external symptom - the MIL lamp lights up when the car is moving, increased fuel consumption, if the car is used for a long time at high speeds, the converter may be damaged .. 1. Defective |
GAS (GAZ) | P0504 | Incorrect brake pedal switch signal. An external symptom is sharp dips in engine operation with partial release of the accelerator pedal (pedal loss), the MIL lamp does not light up, increased fuel consumption. |
GAS (GAZ) | P0505 | Malfunction of the control circuit of the idle speed regulator (IAC). An external sign - the MIL lamp does not go out, the engine starts and stalls, unstable idle speed .. 1. No fixing of the harness block on the regulator - connect the block .. Perform regulator control |
GAS (GAZ) | P0506 | Low idle speed (regulator locked). External symptom - unstable idle (low engine speed) .. 1. Contamination or coking of the regulator - flush the regulator with solvent .. 2. Malfunction of the regulator, weakening of the spring |
GAS (GAZ) | P0507 | High idle speed (regulator locked). External sign - unstable idle (increased engine speed) .. 1. Contamination or coking of the regulator - flush the regulator with solvent .. 2. Malfunction of the regulator, weakening of the spring |
GAS (GAZ) | P0508 | Short circuit to "Mass" of the control circuit of the idle speed regulator - see P0505 |
GAS (GAZ) | P0509 | Short circuit to the "Bortset" control circuit of the idle speed regulator - see P0505 |
GAS (GAZ) | P0511 | Open in the idle speed stepper control circuit - see P0505. |
GAS (GAZ) | P0560 | The voltage of the on-board network is below the operating threshold. An external sign - the engine starts up and stalls, the engine does not start, the voltage indicator of the on-board network drops to zero .. 1. High discharge of the on-board battery - carry out preventive maintenance and recharge the batteries |
GAS (GAZ) | P0562 | Undervoltage in the vehicle electrical system - see P0560 |
GAS (GAZ) | P0563 | Overvoltage of the on-board network. An external sign - the engine starts up, runs unstable and stalls, the voltage of the on-board network according to the indicator "goes off scale" .. 1. Malfunction of the generator or its voltage regulator - carry out preventive maintenance and recharging |
GAS (GAZ) | P0601 | Controller Flash ROM malfunction (checksum error). An external sign - the engine does not start or is unstable and stalls .. 1. Inconsistency of the controller with the standard type - check the marking and read the passport data of the controller |
GAS (GAZ) | P0602 | Malfunction of the RAM (RAM) of the controller. For Euro-3 controllers and below, the code appears every time the controller is disconnected from the on-board battery or engine mass, which means adaptive data and fault codes accumulated by the controller. |
GAS (GAZ) | P0603 | Defective internal RAM or EEPROM controller - P0602. |
GAS (GAZ) | P0604 | Malfunction of the external RAM of the controller - see P0602 |
GAS (GAZ) | P0605 | Controller Flash ROM malfunction (checksum error). An external sign - the engine does not start or is unstable and stalls .. 1. Unauthorized reprogramming of the controller (CHIP tuning) - replace the controller with a regular one .. 2. Damage |
GAS (GAZ) | P0606 | Controller malfunction or error during its initialization - P601 |
GAS (GAZ) | P0615 | Opening of the control circuit of the additional starter relay (DRS). An external sign - the engine does not start .. 1. Check the fuses of the power circuit of the DRS in the mounting block in the passenger compartment or in a special block under the hood .. 2. There is no fixing of the block on the relay - reconnect |
GAS (GAZ) | P0616 | Open or short to ground in the auxiliary starter relay control circuit - see P615 |
GAS (GAZ) | P0617 | Short circuit to the "Bortset" control circuit of the additional starter relay - see P0615 |
GAS (GAZ) | P0618 | Controller External ROM Error - See P0605. |
GAS (GAZ) | P0627 | Open circuit of the control circuit of the electric fuel pump relay. An external sign - the electric fuel pump (EBN) does not turn on, the engine does not start .. 1. Check the fuses in the mounting block in the passenger compartment, in a special block under the hood, or the fuses installed on |
GAS (GAZ) | P0628 | Open or short circuit to "Mass" of the control circuit of the electric fuel pump relay - see P0627 |
GAS (GAZ) | P0629 | Short circuit to "Bortset" of the electric fuel pump relay control circuit. External symptom - the electric fuel pump (EBS) does not turn on, the engine does not start .. 1. Short circuit of the relay control circuit to "+ 12V" - eliminate .. 2. Relay malfunction or not |
GAS (GAZ) | P0630 | Incorrect entry or absence of the VIN-code of the car. External sign - the engine is unstable, increased fuel consumption. the error codes of the incorrect composition of the air-fuel mixture "P0101" appear. "P0105", "P0171", "P0172", "P2187", "P2 |
GAS (GAZ) | P0645 | A / C compressor clutch relay control circuit malfunction. An external symptom - the air conditioning compressor does not turn on .. 1. Check the fuses of the power circuit of the relay in the mounting block in the passenger compartment or in a special block under the hood .. 2. There is no fixation of the number |
GAS (GAZ) | P0646 | Open or short to ground in the A / C compressor clutch relay circuit - see P0645. |
GAS (GAZ) | P0647 | Short circuit to "Bortset" of the A / C compressor clutch relay circuit - see P0645. |
GAS (GAZ) | P0650 | Malfunction of the MIL lamp control circuit (Check Engine). An external symptom is that the engine malfunction lamp MIL does not light up after the ignition is turned on or is on constantly. 1. Check the fuses for the power circuit of the relay in the mounting block in the passenger compartment or in a special |
GAS (GAZ) | P0654 | Malfunction of the tachometer control circuit. External sign - the tachometer needle does not deviate when the engine is running. The tachometer receives 2 pulses from the controller for each revolution of the crankshaft. 1. Broken wire in the ECM harness from the controller side or |
GAS (GAZ) | P0655 | Malfunction of the glow plug warm-up indicator control circuit. An external symptom - the indicator (lamp) of warming up the glow plugs of the engine does not light up after the ignition is turned on or is on continuously, the MIL lamp does not go out. 1. Check the fuses |
GAS (GAZ) | P0685 | Opening of the control circuit of the main relay (RG). An external sign - the MIL lamp does not light up, the electric fuel pump (EBS) does not turn on, the engine does not start .. 1. Check the fuses in the mounting block in the passenger compartment, in the special wiring harness block under the hood, or |
GAS (GAZ) | P0687 | Main relay control circuit short to Bortset - see P0685. |
GAS (GAZ) | P0688 | Open circuit from main relay output - see P0685. |
GAS (GAZ) | P0690 | Short circuit to the “Bortset” of the power circuit of the main relay - see P0685. |
GAS (GAZ) | P0691 | Open or short circuit to "Mass" of the control circuit of the relay of the electric fan No. 1. External sign - the electric cooling fan of the engine (EVO) does not turn on. Turn on / off the EVO relay from the scanner-tester to determine the health of the entire circuit as a whole - |
GAS (GAZ) | P0692 | Short circuit to "Bortset" of the control circuit of the relay of the electric fan No. 1. - see P0691. |
GAS (GAZ) | P0693 | Open or short circuit to ground in the control circuit of the electric fan relay No. 2 - see P0691. |
GAS (GAZ) | P0694 | Short circuit to "Bortset" of the control circuit of the relay of the electric fan No. 2. - see P0691 |
GAS (GAZ) | P1002 | Open circuit of the gearbox solenoid valve. External sign - the car does not switch to gas - the orange indicator of the gas-petrol switch is on, the green blinks, a long beep, the red diagnostics lamp on the switch is on. 1. Electricity is not connected |
GAS (GAZ) | P1005 | One or two cylinder solenoid valves are open in the control circuit - see P1002. |
GAS (GAZ) | P101C | Malfunction of the gas injector circuit A of cylinder 1. External symptom - the car does not switch to gas - the orange indicator of the gas-petrol switch is on, the green blinks, a long beep, the red diagnostic lamp on the switch is on. 1. Not connected |
GAS (GAZ) | P101D | Cylinder 2 Gas Injector Circuit Malfunction - See P101C |
GAS (GAZ) | P101E | Cylinder 3 Gas Injector Circuit Malfunction - See P101C |
GAS (GAZ) | P101F | Cylinder 4 Gas Injector D Circuit Malfunction - See P101C |
GAS (GAZ) | P1030 | Open or malfunction of a chain of the switch "Petrol-gas". External sign - the car does not switch to gas, all indicators are off, a red diagnostic lamp on the switch may be on .. 1. The switch is not connected, wire breakage in the harness of the gas ECM |
GAS (GAZ) | P1033 | Low signal level in the gas level sensor circuit. External sign - the gas level indicators on the gas-petrol switch are off .. 1. No fixing of the harness block on the gas level sensor (ARC) - reconnect the block, fix .. 2. Looseness or |
GAS (GAZ) | P1035 | Gas level sensor signal out of range - see P1033 |
GAS (GAZ) | P1080 | Low signal level in the circuit of the gas temperature sensor in the reducer (DTR) External symptom - the car does not switch to gas - the orange indicator of the gas-petrol switch is on, the green indicator is blinking, a long beep, the red diagnostic lamp is on |
GAS (GAZ) | P1083 | Low signal level in the gas temperature sensor circuit in the filter (DTP). External sign - the car does not switch to gas - the orange indicator of the Gas-Petrol switch is on, the green indicator is blinking, a long beep, the red diagnostic lamp is on |
GAS (GAZ) | P1090 | Low signal level in the absolute pressure (MAP) sensor circuit. An external sign - the car does not switch to gas - the orange indicator of the gas-petrol switch is on, the green indicator is blinking, a long beep, the red diagnostic lamp is on .. AND |
GAS (GAZ) | P1093 | Low signal level in the gas pressure sensor circuit (FGD). An external sign - the car does not switch to gas - the orange indicator of the "Gas-petrol" switch is on, the green indicator is blinking, a long beep, the red diagnostic lamp is on. 1. No f |
GAS (GAZ) | P1102 | Oxygen Sensor # 1 Heater Circuit Resistance Low - See P0030. |
GAS (GAZ) | P1106 | High signal level in the power circuit of the glow plugs. An external sign - the MIL lamp does not go out, the engine does not immediately stall after the ignition is turned off. 1. "Power contacts" of the glow plug relay "stuck" - "ring" the power circuit with an ohmmeter, if necessary |
GAS (GAZ) | P1107 | Low signal level in the power circuit of the glow plugs (open circuit). An external symptom - the engine does not start, the MIL lamp does not go out .. 1. An open in the power circuit of the glow plugs, the glow plugs are not connected, or the power circuit of the wiring harness is faulty - |
GAS (GAZ) | P1115 | Oxygen Sensor # 1 Heater Circuit Malfunction - Refer to P0030. |
GAS (GAZ) | P1123 | "Rich" mixture - limiting additive correction of fuel supply by air. - see P0172 |
GAS (GAZ) | P1124 | "Poor" mixture - limiting additive correction of fuel supply by air. - see P0171. |
GAS (GAZ) | P1127 | "Rich" mixture - limiting multiplicative correction of fuel supply. - see P0172 |
GAS (GAZ) | P1128 | "Poor" mixture - limiting multiplicative correction of fuel supply. - see P0171.1135. No. 1 oxygen sensor heater circuit malfunction - See P0030. |
GAS (GAZ) | P1136 | Mixture "Rich" - additive fuel trim limit for fuel see P0172. |
GAS (GAZ) | P1137 | Lean mixture - maximum additive fuel trim for fuel see P0171. |
GAS (GAZ) | P1140 | Incorrect MAF sensor signal - see P0101. |
GAS (GAZ) | P1141 | Oxygen Sensor # 2 Heater Circuit Malfunction - Refer to P0030. |
GAS (GAZ) | P1171 | Low signal level in the CO-potentiometer circuit. An external sign is increased toxicity and fuel consumption, unstable idling, the engine stalls when the car is braking at idle. The potentiometer can be installed separately or included in |
GAS (GAZ) | P1172 | High signal level in the CO-potentiometer circuit - see P1171. |
GAS (GAZ) | P1230 | Main Relay Control Circuit Malfunction - See P0685. |
GAS (GAZ) | P1335 | Invalid throttle position. External symptom - unstable idle, dips and limitation of engine power, increased fuel consumption .. 1. Deterioration of the parameters of the throttle position sensor (TPS) - wear of the resistive layer |
GAS (GAZ) | P1336 | Discrepancy between the readings of sensors No. 1 and No. 2 of the throttle position External symptom - unstable idle, dips and limitation of engine power, increased fuel consumption .. 1. Deterioration of parameters of one of the throttle position sensors |
GAS (GAZ) | P1351 | Short circuit in the primary circuit of the ignition coil 1 (1/4). External sign - one or two cylinders do not work - the engine “doubles” or “troits” .. 1. Short circuit of the harness wires to the ignition coil between themselves or to “+ 12V”. - "ring" the ohmmeter |
GAS (GAZ) | P1352 | Short circuit in the primary circuit of the ignition coil 2 (2/3) - see 1351. |
GAS (GAZ) | P1386 | An error occurred while performing the internal knock channel test. An external sign - the MIL lamp lights up at increased engine speed, engine power decreases .. 1. Looseness or oxidation of contacts in the pads of the wiring harness - tighten the contacts and fix |
GAS (GAZ) | P1388 | Acceleration pedal position out of range. An external symptom is sharp dips in engine operation with partial release of the accelerator pedal (pedal loss), the MIL lamp does not light up, increased fuel consumption. 1. Check and, if necessary, |
GAS (GAZ) | P1389 | Engine speed out of range. External symptom - the engine does not develop power or operates in the speed limit mode .. 1. Violation of the requirements for vehicle operation - reduce the engine speed .. 2. Fault |
GAS (GAZ) | P1390 | Irreversible restriction of fuel injection due to system malfunctions. External symptom - the engine does not develop power or is operating in the speed limit mode .. 1. Faulty acceleration pedal or throttle device - replace the unit |
GAS (GAZ) | P1391 | Error in the engine monitoring program. 1. Internal controller malfunction - replace the controller .. 2. High level of external or internal electromagnetic interference - check the voltage and ripple in the on-board network, replace the generator or regulator |
GAS (GAZ) | P1410 | Malfunction of the canister purge valve control circuit. An external sign - the MIL lamp does not go out, the smell of gasoline under the hood, increased fuel consumption in summer .. 1. There is no fixation of the harness block on the valve - connect the block. |
GAS (GAZ) | P1426 | Canister Purge Valve Control Circuit Malfunction - Refer to P1410. |
GAS (GAZ) | P1427 | Canister Purge Valve Control Circuit Malfunction - Refer to P1410. |
GAS (GAZ) | P1500 | Open circuit of the control circuit of the electric fuel pump relay. An external sign - the electric fuel pump (EBN) does not turn on, the engine does not start .. 1. Check the fuses in the mounting block in the passenger compartment, in a special block under the hood, or the fuses installed on |
GAS (GAZ) | P1501 | Open or short to ground in the petrol pump relay control circuit - see P1500. |
GAS (GAZ) | P1502 | Short circuit to the "Bortset" of the control circuit of the relay of the electric fuel pump External sign - the engine starts and stalls, unstable idling of a cold engine .. 1. Short circuit of the relay control circuit to "+12V" - eliminate .. 2. Malfunction p |
GAS (GAZ) | P1509 | Overload in the control circuit of the idle speed controller (IAC). External symptom - the engine starts and stalls, unstable idling .. 1. Short circuit of the IAC control circuit to "+ 12V" - eliminate .. |
GAS (GAZ) | P1510 | Short circuit to "Bortset" of the opening circuit of the IAC regulator - see P1509.- for. M17.9.7 |
GAS (GAZ) | P1513 | Short circuit to "Mass" or open circuit of the controller control XX. An external sign - the engine starts up and stalls, unstable idle .. 1. There is no fixing of the block on the IAC - reconnect IAC, fix the block .. 2. Weakening or oxidation of the conta |
GAS (GAZ) | P1514 | Short circuit to "Bortset" of the idle speed regulator control circuit - see P1509. |
GAS (GAZ) | P1530 | A / C compressor clutch relay control circuit malfunction. External symptom - the air conditioner does not turn on .. 1. No fixing of the harness block on the relay - reconnect the relay .. Control the relay from the scanner-tester to determine its circuits .. 2. Reverse |
GAS (GAZ) | P1541 | Open circuit in the control circuit of the petrol pump relay - refer to P1500. |
GAS (GAZ) | P1545 | Throttle position out of range. An external symptom is a limitation of engine power, increased or floating speed XX and increased fuel consumption .. 1. Deterioration of the parameters of the throttle position sensor (DPDZ) - wear of cutting |