How to wash the primer from the car: from paintwork, from glass and plastic
Content
Dried stains are removed with a special sharp scraper, which can be bought at any hardware store. First soften the soil with detergent or water. Then, with a sharp blade at an angle not exceeding 45º, the contamination is carefully scraped off.
It is important to know how to wipe the primer off the car. It hardens and dries quickly. When using unsuitable cleaning agents, it will not be possible to remove the substance quickly. In the worst case, the coating may be damaged.
How to wash primer from the car body
This adhesive mixture contains polymers, water and solvents. After contact with the surface, the liquids evaporate, and the material begins to polymerize.
How to wipe the primer
It hardens and becomes resistant to dissolution. The complexity of soil removal depends on the age of contamination, the type of material and the agent used.
Universal ways
If the particles of the primer got on the body of the machine and did not have time to dry, then they can be easily washed with a wet rag. If a couple of hours have passed and the substance has hardened, then they try to soak it. Procedure:
- apply a damp cloth to the stain;
- fix it for 30-40 minutes (with adhesive tape or with suction cups);
- add liquid without allowing the primed material to dry;
- when it swells, remove it with a granular sponge with an abrasive pad.
The best result is achieved when using boiling water. Hot water will soften the dirt faster.
They are sold at auto parts stores. Method algorithm:
- Put the car in the shade - the mixture is worse removed in the sun.
- Soap a cloth or sponge in warm water.
- Clean the surface with a damp cloth from dirt and sand, so that later the paintwork will not be damaged when wiped with a dry cloth.
- After the machine is dry, spray the lubricant from the clay rod.
- Roll it with a little pressure over the stain several times.
- Reapply lubricant and wipe dry with a towel.
During this procedure, the rod will absorb excess particles on the paint without damaging the car enamel.
You can also wash off the auto-primer if you use an identical composition. The only drawback of the method is that you need to know what substance got on the body. If the composition is unknown, then it will not work to soften and remove pollution.
Step-by-step instruction:
- Prime the stain with a new layer in large quantities on the stain.
- Wait until the fresh composition begins to dissolve the old one (approximately 15-20 minutes).
- Remove all mixture with a sponge or scraper.
A proven method is popular - wipe the primer off the car with a degreaser (gasoline, "white spirit"). It is safe for paintwork. First, the stubborn stain should be washed with water to remove the sand. The cloth should also be clean. Then treat the contamination.
If there is no result, then you can use acetone. This liquid is dangerous for the paintwork, so cleaning should be done with extreme care. Lightly apply the solvent to the fabric so that there are no streams. And carefully treat the contaminated area with soil.
Similarly, according to the scheme described above, toluene, turpentine, ethyl acetate, Antibitum Grass and Nitrosolvents 649 or 650 are used.
Home facilities
Sometimes it is not possible to use universal methods for cleaning. In this case, it will not be difficult to wash off the primer from the car with folk cleaners that are in any home.
An active soda solution perfectly copes with dried-on dirt.
Soda peeling
Recipe for cooking and cleaning procedures:
- Dilute food powder in a 1:1 ratio with oatmeal and water.
- Stir until a liquid porridge.
- Apply the mixture to the stain.
- Wait 50-70 minutes.
- Apply a little baking soda to the wet pad of the abrasive sponge.
- Use it to remove the soaked soil.
- Rinse the surface with water.
Vinegar is a good handy tool for softening a dried mixture. The essence is simply applied to the stain. Then the dirt is gently wiped off, leaving no streaks on the automotive surface.
chemical cleaners
These are professional reagents for removing ingrained dirt. They are used in case nothing helps to wash off the primer from the car. Most of the products contain potent alkalis and acids.
In order not to get burned when working with such chemicals, it is required to wear protective gloves, goggles and strictly follow the instructions for diluting the composition in water.
Как wipe off primer on different surfaces
The adhesive mixture is easy to remove from any type of coating if it has not had time to harden (approximately within 15-20 minutes). If a considerable time has passed, then the method of purification will depend on where the pollution has got.
With glass car
Dried stains are removed with a special sharp scraper, which can be bought at any hardware store. First soften the soil with detergent or water. Then, with a sharp blade at an angle not exceeding 45º, the contamination is carefully scraped off.
If there is no scraper, then you can wash the primer from the car glass with a solvent or vinegar. The liquid is rubbed into the stain with a soft cloth. Then the glass should be rinsed and wiped dry with a microfiber cloth (or paper towel).
Hodrupa, Dopomat and ATLAS SZOP clean glass safely from strong acid products. They must be diluted with water in a certain proportion. In extreme cases, the stain can be removed with undiluted concentrate.
From automotive plastic
Removing the primer from the plastic panel is quite simple with detergents, foam cleaner or an alcohol solution. After the mixture is soaked, it is removed with a rag or scraper.
Do not use aggressive acid-based cleaners. They will just melt the automotive plastic. A hard sponge should also be discarded if you do not need extra scratches on the surface.
The stained area is easy to clean from the stain with vinegar. The essence must be poured into a place with soil and left for an hour. Then rinse off the dirt. Repeat the procedure until the stain completely disappears.
Everyone can wipe the primer off the car body with their own hands. For each type of surface, it is optimal to use a specific method and tool. The less old the contamination, the easier it is to clean. Fresh stains must be removed immediately before they dry out.
