Gas compressor for car refueling: TOP-4 best models
Content
The gas compressor for refueling cars with methane is connected to the central line. To install the station, you must first apply to the gas service for permission, then to the design institute, where they will develop a scheme.
A gas compressor for refueling a car is actually a home station. It can be installed directly on your own site and used autonomously, only for your car.
Everything you need to know about GS
Before you purchase a HS, you need to understand the features of its work:
- A gas compressor for refueling a car can only be used for vehicles running on methane. Those that run on propane will not be able to refuel.
- This is a profitable purchase. Fuel will cost about 2-3 times cheaper than at a stationary gas station. When used for one machine, the equipment pays for itself in a maximum of 2 years.
- The gas compressor for refueling cars with methane is connected to the central line. To install the station, you must first apply to the gas service for permission, then to the design institute, where they will develop a scheme.
- The device does not require any additional equipment.
A gas compressor for refueling a car with methane is quite safe. In any case, the risks of using it are definitely not higher than when using a stove in the kitchen. In case of any breakdown, the station switches off automatically.
HS service
GS is easy to maintain. All that is required:
- Before starting work, make sure that the oil level is sufficient.
- After 55 hours of use, change the oil. Subsequently, this should be done after every 350 hours of use of the HS.
- Once every 12 months Change oil filters and check belt tension.
The time of filling the cylinder with methane depends on the power of the GS. As a rule, 12 cubes are inflated in about 3 hours. At this time, it is not necessary to be near the vehicle. You need to connect the station and disconnect, it will do the rest itself.
Home gas filling FROSP KVD-GS-10
Cost 898 150 rubles. This equipment comes with a 3-year manufacturer's warranty.
KVD-GS-10 is capable of pumping not only methane, but also:
- natural and hydrocarbon gas;
- biogas.
Filling time for a 60 l bottle | 1,5 hours |
Pressure | 250 бар |
A type | Piston |
Engine power | 5,5 кВт |
Noise level | 50 db |
Inlet pressure (recommendation) | 0,03 бар |
Pipe diameter (connection) | 3/4 |
Weight 280 kg. Dimensions 110/75/100 cm. The kit includes:
- user's manual;
- passport;
- certificate;
- hose;
- filling finger.
GS is produced in Taiwan.
Home gas filling FROSP KVD-GS-15
The cost is 1 rubles. Manufacturer's warranty - 197 years. The station is capable of pumping:
- hydrocarbon and natural gas;
- biogas;
- methane.
Pressure | 250 бар |
Engine | three-phase |
Engine power | 75 кВт |
Inlet gas pressure (recommended) | 0,03 |
Pipe diameter (connection) | 3/4 |
Weight 500 kg. Dimensions 150/120/165 cm. The kit includes:
- certificate of conformity;
- instruction;
- hose;
- filling finger.
The station is made in Taiwan.
Home gas filling FROSP KVD-GS-20
The cost is 1 rubles. Manufacturer's warranty - 496 years. GS pumps not only methane, but also hydrocarbon or natural gas, biogas.
Pressure | 250 бар |
Engine | three-phase |
Engine power | 75 кВт |
Inlet pressure | 0,03 |
Pipe diameter (connection) | 3/4 |
Weight 500 kg. Dimensions: 150/120/165 cm. Made in Taiwan. Comes with certificate, manual, hose and filling pin.
Industrial methane gas station FROSP KVD-GS-50
The cost is 2 rubles. Manufacturer's warranty - 619 years. It pumps biogas, hydrocarbon and natural gas, methane.
Upload speed | In 3 hours 50 nm |
Pressure | 250 бар |
Drive unit | Электрический |
Power | 20 l / s |
Inlet pressure (recommendation) | 0,03 |
Pipe diameter (connection) | 2 |
Noise | 80 db
|
Weight 650 kg. Sizes 185/130/170 cm. Produced in Taiwan. Includes certificate, instructions, detailing, hose, filling ring.