How and how to properly lubricate car door hinges when creaking, if rusty
Content
Proper application of lubricant to the stopper and loop will help to avoid unpleasant consequences. Car enthusiasts can carry out such maintenance on their own.
Lubricate the door hinges on the car - one of the options for dealing with creaking. For this, professional substances sold in stores and materials of our own production are used.
Why grease door hinges on a car
Doors are an element of the vehicle that opens and closes very often. Some motorists practically do not carry passengers and go somewhere by car only 2-3 times a week. Others do it more often. But both types of drivers will hear squeaks sooner or later.
This happens due to the use of rubbing mechanisms in the design of doors. Their wear is accelerated if dust and water get inside. A critical wear sound is heard every time it is opened and closed.
Proper application of lubricant to the stopper and loop will help to avoid unpleasant consequences. Car enthusiasts can carry out such maintenance on their own.
How to properly lubricate door hinges on a car
To properly lubricate car door hinges, you need the right substance. Sometimes preparatory work is carried out, without which the result cannot be achieved.
If they are rusty
When the driver ignores the creak for a long time, the moving parts wear out before the appearance of foci of corrosion. Restoration will require the restoration of the door hinges of the car.
To carry out the procedure, you need a rust converter. Half a liter of this substance will cost the motorist 250 rubles. This is enough to clear all loops of plaque, enough to process the thresholds. You can apply lubricant afterwards. It will retain the properties of the purified metal.
When the door is skewed
Another situation when it is necessary to carry out the restoration of doors before applying lubricant is skew. Detailed instructions on how to get rid of it:
- Remove the counter part of the lock to facilitate the adjustment process.
- Check where the door is skewed. Most of the time it sags.
- Loosen the hinges and raise the body element.
- Tighten the fastener and check how correct the position is after that.
- If the door is still lower, then place thin metal plates under the hinge.
- After adjusting the horizontal position. The body element should not be too "recessed".
- At the last stage, adjust the lock and its counterpart.
To consolidate the effect, you need to lubricate the door hinges on the car.
If the hinges creak
Sometimes it is enough to lubricate the door hinges on the car, and not fight rust and sag. But this procedure also has its own nuances.
Detailed algorithm:
- All contaminants that have appeared on the lubricated surface must be removed. To do this, a brush with coarse bristles is enough. It will also remove surface rust. It is recommended to use solvents to quickly cope with plaque.
- Before using the lubricant, clean the surface of chemicals and dry it.
- Apply lubricant to moving parts. It should not fill the loops.
- Open and close the doors 20-30 times, after which they will stop squeaking. In the process, excess grease will be squeezed out, it must be washed with a rag.
If the restoration of car doors is not completed successfully and the squeak remains, it may be sagging.
without removing the door
To properly lubricate the door hinges of the car, it is recommended to dismantle them. But for mild cases, WD-40 or aerosol analogues with a long “proboscis” are suitable. It penetrates into hard-to-reach places, sending a dosed amount of the substance there.
This is enough for the first application. If the situation has not changed after the procedure, then you will have to remove the loops.
How to choose a grease for car hinges
The choice of a substance that can be used to lubricate the door hinges on a car plays a decisive role. The materials presented in stores are divided into two types:
- mineral;
- polymeric.
The latter contain silicone, which retains their properties even in the cold.
Sometimes drivers use technical vaseline. In terms of physical properties, it is similar to the materials sold, but inferior to them in quality. Another substitute is grease. This substance spreads and leaves stains, and also quickly drains from the surface.
Therefore, silicone lubricants are considered the best. They form a film coating that will protect the body element more effectively than grease or petroleum jelly. The substance is distributed evenly, especially if applied from an aerosol.
Useful tips: how and how to lubricate door hinges
Substances with proven effectiveness to lubricate door hinges and locks on the machine:
- Wurth HHS 2000. German production. The substance is effectively distributed over the entire surface. Motorists note high resistance to water and fast adhesion. It comes in a spray can, which allows you to quickly lubricate hard-to-reach car parts. Thickens in minutes and prevents squeaks.
- CRC-MULTILUBE. One of the most common tools for completely processing loops. The manufacturer notes the resistance of the substance to low temperatures. The main advantage is the indication. When the driver applies the gel to the surface of the car, he sees blue spots. This allows you to understand where else to apply the lubricant. But after a few days, the substance loses color and is not striking.
- Liqui Moly Wartungs-Spray Weiss. It differs from the rest by the presence of microceramic particles. The manufacturer developed a tool for interacting with moving parts: locks, hinges, rods. Lubrication protects the application site from corrosion. Based on mineral oil, therefore, operation at temperatures below -30 degrees is not recommended.
The presented substances have a high cost, but their use will eliminate door squeaks for many years. Cheaper analogues are also presented in stores, the effect of their use is doubtful.
Homemade compositions
Motorists, wanting to save money, are developing their own formulations for vehicle lubrication. Most often they create a "liquid key". This is a universal lubricant based on kerosene. It was originally developed to penetrate rusted and stuck joints. It has the ability to displace water and remove rust.
In addition to kerosene, the composition of the liquid includes a solvent and oil. Motorists are experimenting with the contents of the substance, changing some of the components in it.
One of the compositions for lubricating doorways, which is recommended by car owners on thematic forums:
- solvent (white spirit) - 40-50%;
- paraffin distillate - 15-25%;
- hydrotreated isoparaffins - 12-19%;
- carbon dioxide - 2-3%.
The latter substance refers to a mixture consisting of distillate and petroleum solvents.
In its pure form, such substances are practically inaccessible, so they are replaced by simpler, similar in composition. The main property of the finished product is the removal of stuck elements. If the solution copes with this task, then you can use it for loops.