How to replace the lock in the car yourself?

The lock in the car plays a very important role. If damaged, the vehicle can be an easy target for a thief. In addition, it can block at the most unexpected moment, preventing you from entering. Therefore, it is worth at least from time to time to check the correct operation of the locks, and, if necessary, start replacing them. How to do it yourself? We advise!

What will you learn from this post?

• What is the risk of driving with a broken lock?

• How to replace a single lock?

• How to replace the central locking?

TL, д-

Replacing the lock in the car is an important task that should not be neglected. While the assembly of one element does not cause serious problems, the replacement of the central lock is more difficult. Make sure all components are properly disassembled, connected, and then reassembled. The whole complexity of this proposal is that the central lock is a system of wires that must be compatible with each other.

Replacing a single lock or a complete set?

Replacing locks, really seems like a simple thingmay cause problems. In cars of the old type often associated with the need for complex replacement... This is necessary especially when stolen Or key lostand also if this item has been damaged... Then you should buy a new set of locks, including this too ignition switch... There is also a good alternative creating a single item based on the corresponding key.

The problem can arise when you take care of opening all locks with one key - then remains complex replacement of the entire set of locksif the car is not there equipped with an immobilizer... This system electronic coding He is responsible for protection of the car from unwanted start... The coding is so useful that you can replace one lock at a time not to lose the ability to open locks with one key.

How to replace a single lock?

Replacing a single lock this shouldn't cause too much trouble. It's just enough purchase a special insert and install it similar to a regular door. The process must begin from removing the plugand then start unscrewing the screws inside the door with a hex wrench. After that you will need them gently pry Oraz pull out the cassette... As a rule, this is how the lock is changed. However, the problem occurs when the lock is damaged. Then it is necessary dstays inside the door to remove the lock - replacement of the insert itself in this case inadequate... Easier replace the lock in the trunk - in this case it is enough get only inside the damper... The upholstery (bacon) must be remove the latches, unscrew the screws Oraz detach the handle lever. Then you need remove the lock and install a new one, which takes minutes and is child's play.

Replacing the central lock - how to do it?

Replacing the central lock is more of a hassle. First of all, there are many reasons why it starts to work incorrectly, including: faulty remote control, failure of the control unit or drives... Replacing the remote is not difficult, but you must remember set it up with an immobilizer. Moreover, if The lock is controlled by the same remote control as the alarmyou need to buy a lock without a remote control. Thanks to this, the lock will be correctly connected, you will also avoid this. arming problem Oraz removal of car alarms from protection. It is also not one of the hardest replacement of actuators, although it may be necessary dismantling of door panels. However, this turns out to be the most difficult disassembly of the entire central lock and its replacement.

The whole difficulty is that there is a single lock structural elementwhile the central locking is made from the entire cable system, which connects all the doors in the car. Consequently, this game lasts longer and belongs to the need to remove the door from the hinges, as well as upholstery and seals. It is worth having the right tools with you, which will definitely help with the exchange. These include, among others Hex keys, Phillips screwdriverAnd also flat screwdriver.

It is best to start the replacement process by removing the side door, this will simplify the task. getting into the wires of the central locking. In most cars, this is due to this with removal of the lining of side mirrors, door handles Oraz the connecting rod is installed in the glass. Cars with electrics must have all cables are disconnected, otherwise it will collapse.

How to connect the wires when replacing the central locking?

The wires must be outlet from the switchboardwhich is usually located near the steering column. This activity usually includes with the dismantling of a significant part of the door. Следующий шаг assembly Oraz connection of executive mechanisms. The set is the most common one control drive (installed on the driver's side) and actuators (connected to another door). All drives must be in place on the same axis with a lock strand, so that they are not stressed. Last step - connecting a special harness to the control unit and connecting the power supply and alarm. The bundle should be attached to the elements of which it is composed. central moduleor power cable, earth Oraz two signal wires... It is best to check if the lock is working properly. before putting on the sides - if there are problems, You will not need to take them apart again.

Replacement of the lock is required. This is the element that provides the vehicle security and protection against theft. Because, if your lock is broken, be sure to replace it. Good quality locks can be found at avtotachki.com - you are welcome.

Also check:

How do I care for my air conditioner?

Is it time to replace the car? Check for signs of aging car 

What tools should I take with me in the event of a breakdown?

Cut it out,