How to replace pads on Renault Logan

Correct brake pads are essential for safe driving. In order for the brake system to work effectively, it is important to install new ones in a timely manner. On Renault Logan, you can replace the front and rear pads with your own hands, following a simple instruction.

When it is necessary to replace brake pads on Renault Logan

The service life of the pads on Renault Logan is not limited, therefore, replacement is required only if a malfunction occurs or the maximum possible wear of the friction linings. For the correct operation of the brake system, the pad thickness, including the base, must exceed 6 mm. In addition, replacement is required when installing a new brake disc, peeling friction linings from the pad surface, oiling linings or defects in them.

Driving with worn or defective brake pads will affect the effectiveness of the braking system and could lead to an accident. The need for replacement is manifested by symptoms such as bumps, rattling, squeaks when the car stops and an increase in braking distance. In practice, Renault Logan pads wear out after 50-60 thousand kilometers and begin to rattle.

Wear is not always even on both pads.

The brake mechanism of a back wheel with the removed drum: 1 — a back brake shoe; 2 - spring cup; 3 - parking brake drive lever; 4 - space; 5 - upper coupling spring; 6 - working cylinder; 7 - regulator lever; 8 - control spring; 9 - front block; 10 - shield; 11 - parking brake cable; 12 - lower connecting spring; 13 - support post

Tool kit

To install new brake pads yourself, you need to prepare:

• Jack;
• screwdriver with a straight slot;
• brake lubricant;
• an asterisk key for 13;
• fixed key at 17;
• pad cleaner;
• container with brake fluid;
• sliding clamps;
• anti-reverse stops.

What consumables are better to choose: video guide "Behind the wheel"

How to change the rear

To replace a set of rear pads on a Renault Logan, follow the steps below.

1. Block the front wheels and raise the rear of the machine.Raise the car body
2. Unscrew the fixing screws of the wheels and remove them.
   
   Remove the wheel
3. Slide the pad against the brake disc with a flathead screwdriver to push the piston into the slave cylinder.
   
   Push the piston into the cylinder
4. With a 13 wrench, unscrew the lower caliper mount, holding the nut with a 17 wrench so that it does not accidentally turn.Remove the lower caliper bracket
5. Raise the caliper and remove the old pads.
   
   Open the caliper and remove the tablets
6. Remove the metal plates (guide pads), clean them of rust and plaque, and then return to their original position.
   
   Clean the plates from rust and debris
7. Remove the caliper guide pins and treat them with brake grease.
   
   Lubricate mechanism
8. Install the block kit and assemble the frame in reverse order.
   
   Close the cover and tighten the bolt

How to change rear pads with a lot of wear (video)

How to replace the front

Installation of new front pads is carried out according to the following instructions.

1. Block the rear wheels with wedges and raise the front wheels.Front body lift
2. Remove the wheels and insert a screwdriver into the gap between the caliper and shoe, pushing the piston into the cylinder.
   
   
   
   push piston
3. Using a wrench, unscrew the lock of the caliper and lift its folding part.Remove the caliper bracket
4. Remove the pads from the guides and remove the fixing clips.
   
   Take out the old pads and staples
5. Clean the pads from traces of corrosion.
   
   Use a metal brush
6. Apply grease to the guide surface and install new pads.
   
   Install new pads, after lubricating the guides
7. Lower the caliper to its original place, tighten the mounting bolt and install the wheel.
   
   Lower the caliper and screw in the fixing bolt, put the wheel back

Video on how to change the front

The specifics of replacing pads on a car with ABS

When replacing brake pads on a Renault Logan with ABS (anti-lock braking system), some additional steps must be taken. Before installing the pads, you must remove the ABS sensor so as not to damage it. The ABS sensor cable, located under the steering knuckle, must not be removed during operation, so it is important to be careful and ensure your own safety.

The design of brake pads for vehicles with ABS has a hole for the system sensor. When planning a replacement, it is important to purchase the correct set of pads that are compatible with your anti-lock braking system.

Tips for choosing the right size consumables in the video

Problems when doing work with your own hands

When replacing pads with Renault Logan, there is a risk of problems that must be fixed for the brakes to work properly.

• If the pads cannot be removed without effort, it is enough to treat the place of their landing with WD-40 and start working in a few minutes.
• When, when closing the caliper, the piston element protruding from the working cylinder creates an obstacle, it is necessary to completely clamp the piston with sliding pliers.
• To prevent the brake fluid from flowing out of the hydraulic reservoir when installing the pads, it must be pumped into a separate container and topped up after completion of work.
• If during installation the protective cover of the caliper guide pins was damaged, it must be removed and replaced with a new one, after removing the brake pad guide bracket.
• If there are gaps between the brake pads and discs, you must press the brake pedal so that the components get into the right position.

When the pads are replaced correctly, the brake system will work properly, and driving safety will also increase. If you spend a little time installing the pads yourself, you can extend the life of the brake mechanism and avoid dangerous situations on the road.