Which car compressor is better to buy for a jeep
To prevent burns or other injuries from the operating unit, it is closed with a hard protective cover, into which the controls and terminals for connecting the air hose are integrated.
Deciding which car compressor is better to buy for a jeep will help take into account the requirements for vehicles of this type in various traffic conditions.
Technical specifications
For SUVs, the difference in tire pressure, depending on the driving mode, can reach 3 atmospheres. This means that the compressor must confidently inflate the wheels in excess of the established average rate. The required volume of air exceeds that of a conventional passenger car. Therefore, it is better that the pump performance is higher.
When choosing which car compressor is better to buy for a jeep for its reliable operation, it is necessary to take into account the position of the device in the rating and the compatibility of the following technical parameters.
Performance
To inflate a set of tires of large sizes (from 17 inches and above) or high profile, it is advisable to buy compressors with a real capacity of at least 50 liters per minute within the specified duty cycle.
Duration of continuous work
A long load on a car compressor for a jeep causes overheating of its working units and a sharp drop in performance. Most often this happens with non-stop air supply at the pump power limit. You should not rely on this indicator for tire inflation. The achievement of the required pressure level from zero in a couple of minutes should be considered the norm. For a jeep, a car compressor is better, coping with adjusting the pressure of all wheels within 10-15 minutes, which usually falls within the technical specifications of the pump.
Ultimate pressure
This indicator characterizes the level of pressure developed at the compressor outlet under given operating conditions (supply voltage is normal, the device is not overheated). 10 atmospheres is enough for a productive unit.
Number of pistons
For a jeep, it is better to buy a car compressor that uses a two-piston mechanism, as it is more efficient and less noisy. But there are also single-piston models that meet the necessary requirements.
Housing material
The oil-free design of the piston group is prone to rapid heating due to friction. Therefore, productive compressors are placed in a metal case. An additional ribbed jacket is provided for cooling the pressurized air supply unit. This contributes to efficient heat dissipation, increases the time of continuous operation.
Length of power wire and air hose
The way the power supply affects the performance of the pump. A standard thin electric cord switched through the car's cigarette lighter can cause the on-board fuse to trip when overloaded. In addition, a large current consumption causes a significant voltage drop on the power wires (2-3 volts). This leads to a loss of motor power and an increase in tire inflation time. It is better not to buy such a car compressor for a jeep.
The length of the air hose in the normal or spring version should provide access to the nipples of all wheels, including the spare.
Fitting design
The connection of the air hose to the body of a powerful compressor is most often implemented using a quick-release or threaded fitting. The same applies to the nozzle on the tire nipple.
Availability of additional functions
When choosing which car compressor is better to buy for a jeep, you should keep in mind important optional features:
- built-in blocking of power supply at an overheat;
- replaceable suction air filter;
- nozzles and adapters for inflatable components of household, household and sports equipment
- built-in flashlight with replaceable filters (required for a car in the absence of natural light);
- digital display for fine adjustment of tire pressure level.
Many brand-name tire inflation devices are equipped with this functionality. Some of them have quite impressive dimensions and you will need to find a convenient permanent place for them in the trunk.
Rating of the best car compressors for a jeep
A review of a number of models can help you choose and purchase a high-quality and inexpensive device that fully meets the consumer's expectations.
Viair 40047 400P-RV
A high-performance portable car compressor for a jeep, according to the manufacturer, provides pumping of a 275/80/22,5 wheel from 5 to 6 atmospheres in half a minute.
Assembled in an all-metal housing with heat sink fins and a threaded socket for a removable air filter. Attaches to a metal corrugated platform. The extendable two-section hose is equipped with quick-locks for connection to the air connection integrated into the carrying handle. The kit includes a special extension with a deflator and a pressure gauge for jeeps with dual rear pairs of wheels. Specifications:
Parameters | The values |
Supply voltage | 10-13,5 volts |
Current consumption | 30 amp |
Maximum working pressure | 10,5 бар |
Hose inlet performance | 65 l / min |
Length of each air hose | 9 meters |
Power cable length | 2,5 meters |
Net weight | 4,8 kg |
There is an emergency shutdown device and an air blocking valve. The unit is completed with a transport tarpaulin bag and adapters for use with household inflatable equipment.
PORTER CABLE C2002
A wheel-shaped automobile compressor is mounted on a circular compressed air tank that simultaneously serves as a support. To prevent burns or other injuries from the operating unit, it is closed with a hard protective cover, into which controls and terminals for connecting the air hose are integrated.
Its connection to the pump is realized using a quick-clamp fitting. Technical details:
Parameter | Value |
Supply voltage | 120 Volts |
Capacity at 3 bar | 98 l / min |
Capacity at 5,7 bar | 73 l / min |
Compressed air tank volume | 22 l |
Maximum developed pressure | 10,5 бар |
Power | 0,8 l. from. |
Net weight | 13,5 kg |
The kit includes a set of nozzles, including a special extension for pumping the inner rear wheels in cars with their dual installation.
VIAIR 45053 Silver
Universal single-piston all-metal compressor on a support platform with a removable air filter. There is a stackable spring hose with a pressure gauge and a deflator.
Connection to the tire nipple on the one hand and the pump fitting on the other is carried out by quick-detachable connectors. There is an adapter for access to the inner rear wheels in case of their dual design. The electrical voltage is removed from the battery terminals. Technical data in the table:
Parameter | value |
Supply voltage | 12 Volts |
Maximum working pressure | 10,5 бар |
The total length of the main and additional air hoses | 18 meters |
Power cord length | 2,5 meters |
Initial performance | 50 l / min |
Current consumption | 25 amp |
Weight of the device in the transport bag | 8,1 kg |
Built-in automation ensures safe operation. For storage and transport, there is a bag with additional pockets that accommodate air hoses and work accessories. Good for an SUV.
Aggressor AGR-50L
Single-piston pump in a metal case with a lantern integrated into the end end, equipped with a replaceable red light filter with two operating modes.
The spring hose is connected to the unit's fitting with a quick-clamp connector. At its other end there is a branch pipe with a built-in dial gauge. Threaded connection to the bus nipple, power supply directly from the battery via a fuse integrated in the cable. Technical details in the table:
Parameters | Values |
Supply voltage | 12 Volts |
Maximum current consumption | 23 amperes |
Maximum working pressure | 10 бар |
Initial performance | 50 l / min |
Air hose length | 5 meters |
Electric cable length | 3 meters |
Weight | 2,9 kg |
Storage and transportation of the unit in a cloth bag. All accessories, including nozzles for third-party inflatable objects, are placed in it.
Kensun Tire Inflator
This compressor has extended functionality due to the additional ability to connect to the AC mains. To do this, there is an AC / DC mode selector and a special socket on the end of the plastic case. Communication with the car's on-board network through the cigarette lighter socket. The pressure indicator is a digital display on the top cover with an accuracy of 0,1 atmosphere. The control panel for the pumping / pressure reduction mode is also located here.
Some modifications, in addition to the LED lamp on one of the end surfaces, have an integrated fan to improve the cooling of the unit. Technical data:
Parameter | Value |
Supply voltage | DC/AC 12V/110(220)V |
Power | 120 W |
Electric cable length | 3 m |
Air hose length | 1,8 m |
Maximum pressure | 7 бар |
Performance | 30 l / min |
Net weight | 2,2 kg |
AstroAI 150 PSI
A miniature pump in a plastic case with controls and pressure control located on the top panel on a digital display with a choice of units of measurement.
There is a special removable spigot with quick-release connector for alternative connection. This slightly lengthens the air hose with a threaded end. On the ends, an LED lamp is mounted on one side, and on the other, switches for starting the compressor and light. Technical details in the table:
Parameters | The values |
Supply voltage | 12 Volts |
Electric cable length | 3 meters |
Air cable length | 0,5 meters + 0,2 meters branch pipe |
Developed pressure | 10 бар |
Power | 120 watts |
Time of continuous work | 15 min max |
Weight | 1 kg |
The product is completed with adapters for inflating sports equipment and inflatable household items.
Berkut R20
Assembled in a metal moisture-resistant case, equipped with cooling fins of sufficient area. An air filter with a replaceable element made of foam rubber is fixed at the end of the product. The wide metal base provides stability when working. Powered directly from the battery via a cable with an integrated 40A fuse.
The unit is equipped with a thermal relay. The twisted air hose is provided with a quick-clamp connector for connection to the pump nozzle. At the other end is a control pressure gauge with a deflator valve. Technical data in the table:
Parameter | value |
Voltage | In 12 |
Current | A 30 |
Pressure maximum / working | 14 bar / 4 bar |
performance | 72 l / min |
Power cable length | 2,4 m |
Air hose length | 7,5 m |
Weight | 5,2 kg |
The kit includes a set of adapters for household, sports equipment and inflatable boats, as well as a good-quality transport bag.
PORTER CABLE CMB15
Lubrication free high performance fully enclosed compressor to avoid injury from hot or moving parts. The built-in reservoir is designed to maintain a maximum pressure of 10.5 bar for increased uptime. The control panel on the bevel of the front panel allows you to control the pumping process using two pressure gauges.
Parameter | Value |
Supply voltage | In 120 |
Capacity at 0,8 bar | 85 l / min |
Capacity at 6,5 bar | 56 l / min |
Maximum working pressure | 10,5 бар |
Power | 0,8 l. from. |
Air tank volume | 5,7 l |
Net weight | 9 kg |
You can purchase a pump for pumping any inflatable objects - the kit includes 8 different nozzles.
AVS KS900
Compact all-metal automotive compressor on a stable platform with a circular stiffener. The transport handle is covered with heat-resistant material to protect against burns. The connection of the expandable air hose to the compressor fitting is through a quick-clamp connector, and to the tire nipple is threaded.
Pressure control on the pressure gauge on the hose nozzle. There is also a deflator. Sophisticated cooling design makes long continuous operation possible. Technical data:
Parameters | Values |
Voltage | In 12 |
Current | 30 a |
Pressure maximum / working | 10 бар |
performance | 90 l / min |
Power cable length | 3 m |
Air hose length | 5 m |
Weight | 4,5 kg |
The compressor is completed with a set of adapters for pumping household inflatable equipment and a cloth bag for transportation and storage.
TIREWELL 12V
A good two-piston car compressor in a metal case. End ends made of plastic at the same time serve as its supports. They contain devices for switching on and emergency shutdown in case of overheating. The connection to the power source is combined - through the cigarette lighter or directly to the battery using an adapter. The spring-loaded extension cable is connected to the air outlet hose integrated with the pump with a threaded connection.
Technical data:
Parameter | value |
Supply voltage | In 12 |
Current | 56 l / min |
Input performance | 10,5 бар |
Developed pressure | 10,5 бар |
air hose | 0,5 m + 5 m |
Power cable | 3,5 m + 0,5 m battery attachment |
Device weight | 3 kg |
The package includes a transport case and a set of adapters for inflating household and sports equipment.