Gazelle stove motor

It is difficult to imagine a modern car without a cabin heater. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and movement becomes difficult or even impossible. To prevent this from happening, hot air from the furnace is directed onto the glass, which heats them up and moisture does not condense on them.

Operating principle

The interior heating of the Gazelle Business, like many other cars, is carried out thanks to the heat generated by the car's engine. Heat in the engine is released during the combustion of fuel and friction surfaces. To remove heat from hot parts, a cooling system is built into the engine. It removes heat through the refrigerant. For interior heating, a heated liquid is used, which is supplied through pipes and lines to the radiator, due to which it heats up. To distribute heat throughout the passenger compartment, an electric motor with an impeller draws cold air through a heated radiator. After that, the heated air through the deflectors enters the cabin. By operating the dampers, you can direct the hot air to the right places. To control the air temperature, a heater tap is installed, with which you can adjust the amount of coolant passing through the radiator. A rheostat is installed to change the fan speed. All control is electronic. From the control unit, the signal goes to the gear motor, which, in turn, opens or closes the gate.

Diagnostics

Replacing the Gazelle stove motor Business is a very long and laborious process. And so that this work is not in vain, it is necessary to ensure its implementation.

1. With the engine off and the ignition on, turn the levers and check all modes. When switching, clicks of the operation of the gear motor should be heard. If no operation is heard, check the power supply of the control unit.
2. Next, you should try to change the position of the engine speed knob. If it does not work in all modes except the fastest, then the resistor is out of order. If there is no rotation in any of the positions, then it is necessary to check the power in the engine.
3. It is necessary to check the correctness of the heater radiator hoses: with a hot engine and a handle in hot air, they should be hot. If they are cold, then you need to check the faucet or actuator.

Replacing the motor of the GAZEL stove

GAZTEC.ru — Repair, painting, HBO, spare parts for GAZ, UAZ. Website: Our VK group: ...

Quick replacement of the engine speed governor of the gazelle business stove

A quick and easy way to replace the stove motor with a GAZelle.

Repair

Having checked everything and with full confidence we can say that the faulty element is the stove motor, only after that you should proceed to disassemble the dashboard, since to remove the heater it is necessary to disassemble the entire torpedo assembly. For this operation, we need a set of heads and screwdrivers. To get to the heater, you need to disassemble the entire instrument panel.

1. First of all, we will secure the workplace by disconnecting the positive cable from the battery.
2. Remove the side plastic covers.
3. Put speakers in the dashboard.
4. Disconnect the instrument panel.
5. Remove the left and right side covers.
6. We unscrew the heater control unit with deflectors.
7. Remove the deflector under the windshield.
8. Unscrew and remove the glove box located below, on the passenger side.
9. Next, unscrew the bolts that secure the heater to the car from the engine side.
10. Drain the engine coolant into a clean container.
11. Dismantle the pipes through which the engine coolant enters the heater radiator (there will be coolant residues in them, measures must be taken to prevent leakage of coolant into the passenger compartment).
12. Then stick tags on the wiring terminals (so as not to mix them up during assembly) that fit the devices and disconnect them.
13. Next, unscrew the fasteners that secure the steering column to the dashboard, after which it will lie freely on the driver's seat.
14. Then pull out the torpedo (you will need an assistant for this procedure), removing it from its place, carefully make sure that there are no unconnected terminals left, if any, they must be disconnected.
15. And put the panel on something soft so as not to scratch it.
16. Next, we disassemble the iron frame, which is located behind the removed torpedo, and also remove it together with an assistant.
17. Then we disconnect the air ducts coming from the stove (it is better to mark or photograph them so as not to be confused during assembly).
18. Now you can proceed to the "bifurcation" (unscrew the screws and remove the brackets).
19. We get an electric motor with an impeller. Now you need to check it and understand whether the thing is repairable or not. In this case, it will be more convenient to replace the engine, since it is impossible to say exactly how long the repaired engine will last. And in case of failure, you will have to redo all the previous work.
20. After repairing or replacing the motor, we assemble everything in the reverse order. And before the final assembly, we check its operation in all modes, and if everything works, then we complete the work.

These are the recommendations that can be given if the Gazelle Business stove motor does not work. Of course, it is unpleasant that because of such a trifle as an electric motor, you have to disassemble the entire torpedo, but without heat in the cabin it is inconvenient and unsafe to drive. Of course, you can contact the service, where it will be replaced and repaired. But if you have time and experience, you can do all the repairs yourself.

How to remove the Gazelle stove motor

How to replace the engine (fan) of a gas oven Gazelle

It is difficult to imagine a modern car without heating. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and driving becomes difficult or impossible. To avoid this, the hot air from the oven is directed towards the panes, which causes them to heat up and prevents moisture from condensing on them.

How does it work

Internal heating is turned on by the Gazelle Business, like many other cars, it moves due to the heat generated by the car's engine. Engine heat is released from the combustion of fuel and from abrasive surfaces. The cooling system is built into the engine to remove heat from hot parts. Elimination of heat, cooling water. To heat the interior, a heated liquid is used, which is supplied through pipes and tubes to the radiator, due to which it warms up. To distribute heat throughout the cabin, the vane motor draws cool air through a heated radiator. After that, the heated air enters the cabin through the partitions. By operating the dampers, you can direct the hot air to the right places. To control the temperature of the air heater, a mixer is installed, with which you can adjust the amount of coolant passing through the radiator. A rheostat is installed to change the fan speed. All controls are electric. From the control unit, the signal is sent to the gearbox, which in turn opens or closes the shock absorbers.

diagnostics

Replacing the stove engine Gazelle Business. This is a very long and lengthy process. And so that this work is not in vain, you need to make sure that you need it.

1. With the engine off, with the ignition on, turn the levers and check all modes. When shifting, the sound of the gearbox is heard. If nothing is heard, check the power supply to the control unit.
2. Next, check the change in the position of the engine speed control. If this fails in all modes except Livest, the stamina fails. If there is no rotation in any position, check the power of the motor itself.
3. It is necessary to check the correctness of the heater radiator hoses: with a hot engine and a handle in hot air, they should be hot. If they are steep, then you need to check the crane or actuator.

Repair

After everything has been checked and it will be possible to say with certainty that the stove engine is faulty, only then can the dashboard be removed, since to remove the heater it is necessary to remove the entire torpedo assembly. For this operation, we need a set of heads and screwdrivers. To get to the dispenser, you need to remove the entire board.

1. First of all, we will secure the workplace by disconnecting the positive cable from the battery.
2. Remove the side plastic covers.
3. Insert the speakers into the dashboard.
4. Disable board.
5. Remove the left and right side covers.
6. We unscrew the partition heating control unit.
7. Remove the deflector under the windshield.
8. Unscrew and remove the glove located at the bottom of the passenger side.
9. Then unscrew the bolts that secure the heater to the machine from the engine side.
10. Drain the engine coolant into a clean container.
11. Remove the pipes that carry the coolant from the engine to the heater radiator (there will be coolant residues in them, you must make sure that the coolant does not get into the passenger compartment).
12. Then mark the wiring terminals (do not mix up during reassembly) that fit the devices and disconnect them.
13. Next, we unscrew the fasteners that are attached to the dashboard, after which it freely rests on the driver's seat.
14. Then remove the torpedo (an assistant is needed for this procedure), pulling it out of place, making sure that there are no disconnected terminals, if any, then they should be disconnected.
15. And put the pillow on something soft so as not to scratch it.
16. Next, disassemble the iron frame, which is located behind the removed torpedo, and remove it together with an assistant.
17. Then disconnect the air ducts coming out of the oven (it is better to mark or photograph them so as not to be confused during assembly).
18. Now you can start from the middle (unscrew the screws and remove the supports).
19. We get an electric motor with a wing. Now you need to test this and see if the item is repairable or not. In this case, it would be more appropriate to replace the engine, since it is impossible to say exactly how long the engine will be repaired. And in case of failure, all the previous work will have to be done again.
20. After repairing or replacing the motor, we assemble everything in the reverse order. And before the final assembly, we check its operation in all modes, and if everything works, then we finish the work.

These recommendations can be given if this business of a motor gas stove does not work. Of course, it is unpleasant that because of such a trifle as an electric motor, you have to disassemble the entire dashboard, but without heat in the cabin, driving is inconvenient and dangerous. Of course, you can contact the service, where they will be replaced and repaired. But with time and experience, all repairs can be done independently.

The best prices and conditions for buying new cars

Replacing the Motor Heater Gazelle Business

Without this, it is difficult to imagine the sound insulation of the interior of a modern car. This makes the journey not only comfortable, but also safe. In the cold season, moisture condenses on the cold glass, and movement becomes difficult or impossible. To avoid this, the hot air from the oven is directed towards the panes, which causes them to heat up and prevents moisture from condensing on them.

How does it work

Heating of the interior of the Gazelle Business As in many other cars, this is carried out due to the heat generated by the car's engine. Engine heat is released from the combustion of fuel and from abrasive surfaces. The cooling system is built into the engine to remove heat from hot parts. Elimination of heat, cooling water. To heat the interior, a heated liquid is used, which is supplied through pipes and tubes to the radiator, due to which it warms up. To distribute heat throughout the cabin, the vane motor draws cool air through a heated radiator. After that, the heated air enters the cabin through the partitions. By operating the dampers, you can direct the hot air to the right places. To control the air temperature, a shut-off valve is installed, which can control the amount of coolant passing through the radiator. A rheostat is installed to change the fan speed. All controls are electric. From the control unit, the signal is sent to the gearbox, which in turn opens or closes the shock absorbers.

diagnostics

engine replacement Gas stove Business. This is a very long and drawn out process. And so that this work is not in vain, you need to make sure that it is necessary.

1. With the engine off, with the ignition on, turn the levers and check all modes. When shifting, a click of the engine and gearbox should be heard. If nothing is heard, check the power supply to the control unit.
2. Next, check the change in the position of the engine speed control. If this fails in all modes except Livest, the stamina fails. If there is no rotation in any position, check the power of the motor itself.
3. Make sure the hoses fit into the heater core - when the engine is hot and the handle is exposed to hot air, they should be hot. If they are cold, check the faucet or actuator.

Repair

After everything has been checked, and it will be possible to say for sure that the stove motor is a faulty element, only then should the board be disassembled, since in order to remove the heating element, it is necessary to remove the entire torpedo assembly. For this operation, we need a set of heads and screwdrivers. To get to the parent, you need to disassemble the entire instrument panel.

1. First of all, we will secure the workplace by disconnecting the positive cable from the battery.
2. Remove the side plastic covers.
3. Insert the speakers into the dashboard.
4. Disable board.
5. Remove the left and right side covers.
6. We unscrew the partition heating control unit.
7. Remove the deflector under the windshield.
8. Unscrew and remove the glove located at the bottom of the passenger side.
9. Then we unscrew the bolts securing the heater to the car from the engine side.
10. Drain the engine coolant into a clean container.
11. Remove the pipes that lead the coolant from the engine to the radiator insulation (these will remain with the coolant, care must be taken to prevent coolant from entering the passenger compartment).
12. Then mark the wiring terminals (do not mix up during reassembly) that fit the devices and disconnect them.
13. Then unscrew the fasteners that secure the steering column to the steering wheel, and then it will fall freely into the driver's seat.
14. Then remove the torpedo (an assistant is needed for this procedure), pulling it out of place, making sure that there are no disconnected terminals, if any, then they should be disconnected.
15. And put the pillow on something soft so as not to scratch it.
16. Next, disassemble the iron frame, which is located behind the removed torpedo, and remove it together with an assistant.
17. Then disconnect the air ducts coming out of the oven (it is better to mark or photograph them so as not to be confused during assembly).
18. Now you can start from the middle (unscrew the screws and remove the supports).
19. We get an electric motor with a wing. Now you need to test this and see if the item is repairable or not. In this case, it would be more correct to replace the engine, since it is impossible to say exactly how long the engine will be repaired. And in case of failure, all the previous work will have to be done again.
20. After repairing or replacing the motor, we assemble everything in the reverse order. And before the final assembly, we check its operation in all modes, and if everything works, then we finish the work.

These recommendations can be given if the engine is not running. Stoves Gazelle Business. Of course, it is unpleasant that because of such a trifle as an electric motor, you have to disassemble the entire torpedo, but without heat in the cabin it is inconvenient and dangerous to drive. Of course, you can contact the service, where they will be replaced and repaired. But with time and experience, all repairs can be done independently.

The best prices and conditions for buying new cars

How to replace the motor (fan) of the Gazelle Business stove

It is difficult to imagine a modern car without a cabin heater. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and movement becomes difficult or even impossible. To prevent this from happening, hot air from the furnace is directed onto the glass, which heats them up and moisture does not condense on them.

How to remove a gazelle stove fan business

In general, the stove asked for a long time, howled in waves, squealed in potholes, and then one fine day it began to howl constantly. it was decided to change it myself (a toad would have strangled 7 for a replacement), except that the engine shield would make some noise ... I decided to try to light it completely, uploading a bunch of videos and forums and did not find any data. The real problem was that it was very difficult to find a garage for such a crocodile, and stocking up on a 220v heater, I went to open it with spare parts to replace the stove motor ... I also bought: 4 sheets of STP AERO PREMIUM (enough 2,5) 2 sheets of BIPLAST A 15 (1,5 is enough)

Below is a picture with the location of the screws! Attention, you will need to remove: - Battery brand - Side grilles - Plastic with places for standard speakers - Side panel linings - Dashboard - Central part (xs as the name) between 4.5 and 6.7 - Lower glove box - Right cup holder - pull with a plastic screwdriver under the windshield glass (xs what is it called) ...

If all went well, open the hood and take a look

We unscrew, go into the salon, the panel should hang. It is required to unscrew the pipes from the stove radiator in the cabin

It is difficult to imagine a modern car without a cabin heater. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and movement becomes difficult or even impossible. To prevent this from happening, hot air from the furnace is directed onto the glass, which heats them up and moisture does not condense on them.

How to change the stove motor for a gazelle - DIY car repair

How to replace the motor (fan) of the stove Gazelle Business

It is difficult to imagine a modern car without a cabin heater. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and movement becomes difficult or even impossible. To prevent this from happening, hot air from the furnace is directed onto the glass, which heats them up and moisture does not condense on them.

Loan 9,9% and installments 0%

The stove in the cabin creates comfortable conditions for the driver and passengers. Sometimes this device fails due to problems with the heatsink. This device is the most important structural element of any heater. It is for this reason that it is important to know how the stove radiator is replaced on the Lada Kalina and other domestic cars.

The heater on the Lada Kalina is one of the main advantages of the car. However, over time, car owners may notice various deviations in the operation of the stove. The presence of antifreeze on the mats is the main reason to take up the elimination of a stove leak. Do not delay with this, because antifreeze can flood the electronic control unit, which will lead to more serious problems over time.

The following problems most often arise with the Lada Kalina radiator:

• The channels were clogged, which caused an increase in pressure in the system and, as a result, a rupture of the tube;
• Wear of pipes during the operation of the car;
• Air lock in the system.

The presence of oily fluid around the device is the first sign that it needs to be replaced. Replacing the stove with Lada Kalina is complicated by the fact that it is rather complicated and unfriendly in terms of repair and replacement of parts. To get to the radiator, which is located in the center console, you need to do quite a lot of work to dismantle the various elements. How to do all the work without removing the panel?

Related article: SHRUS device, how to determine which grenade crunches

One of the most accurate and affordable ways to replace a stove with a Lada Kalina is to cut the pipes or the heater body. It is the second option that is more preferable for many car owners, since it is enough to do the work once and forget about problems with disassembly in the future in the event of a malfunction.

To cut the body of the stove, it is best to arm yourself with a soldering iron or a wood burner. The first step is to remove the "negative terminal" and remove the flywheel cover. For the convenience of performing all work, it is also desirable to turn the regulator on the heater control panel to the “cold” position in order to provide unhindered access to the radiator. Then you must follow the following procedure:

1. Unscrew the three nuts on the accelerator pedal and place it inside for later convenience.
2. Remove the air duct with the air filter.
3. Remove the pipes going to the radiator.
4. Cut the maximum hole size at the bottom of the panel.
5. Remove the radiator.

However, it is not always possible to easily receive a broken device from the owners of Lada Kalina. We must try to remove the entire radiator at the same time and the bracket and seal through the cut hole. Sometimes difficulties arise - a new radiator does not pass.

You will have to shorten the pipes by 1-1,5 cm, but if you managed to disassemble the old device without problems, you may be able to install a new one without problems.

See also How to remove the starter on the Audi 100

After that, it is necessary to assemble in the reverse order and glue part of the cut panel.

Operating principle

The interior heating of the Gazelle Business, like many other cars, is carried out thanks to the heat generated by the car's engine. Heat in the engine is released during the combustion of fuel and friction surfaces. To remove heat from hot parts, a cooling system is built into the engine. It removes heat through the refrigerant. For interior heating, a heated liquid is used, which is supplied through pipes and lines to the radiator, due to which it heats up. To distribute heat throughout the passenger compartment, an electric motor with an impeller draws cold air through a heated radiator. After that, the heated air through the deflectors enters the cabin. By operating the dampers, you can direct the hot air to the right places. To control the air temperature, a heater tap is installed, with which you can adjust the amount of coolant passing through the radiator. A rheostat is installed to change the fan speed. All control is electronic. From the control unit, the signal goes to the gear motor, which, in turn, opens or closes the gate.

Diagnostics

Replacing the Gazelle stove motor Business is a very long and laborious process. And so that this work is not in vain, it is necessary to ensure its implementation.

1. With the engine off and the ignition on, turn the levers and check all modes. When switching, clicks of the operation of the gear motor should be heard. If no operation is heard, check the power supply of the control unit.
2. Next, you should try to change the position of the engine speed knob. If it does not work in all modes except the fastest, then the resistor is out of order. If there is no rotation in any of the positions, then it is necessary to check the power in the engine.
3. It is necessary to check the correctness of the heater radiator hoses: with a hot engine and a handle in hot air, they should be hot. If they are cold, then you need to check the faucet or actuator.

When the heater electric motor needs to be replaced

There are several signs that will tell the car owner that something is wrong with the heater motor. Here are the most common:

Repair

Having checked everything and with full confidence we can say that the faulty element is the stove motor, only after that you should proceed to disassemble the dashboard, since to remove the heater it is necessary to disassemble the entire torpedo assembly. For this operation, we need a set of heads and screwdrivers. To get to the heater, you need to disassemble the entire instrument panel.

1. First of all, we will secure the workplace by disconnecting the positive cable from the battery.
2. Remove the side plastic covers.
3. Put speakers in the dashboard.
4. Disconnect the instrument panel.
5. Remove the left and right side covers.
6. We unscrew the heater control unit with deflectors.

• Remove the deflector under the windshield.
• Unscrew and remove the glove box located below, on the passenger side.
• Next, unscrew the bolts that secure the heater to the car from the engine side.
• Drain the engine coolant into a clean container.
• Dismantle the pipes through which the engine coolant enters the heater radiator (there will be coolant residues in them, measures must be taken to prevent leakage of coolant into the passenger compartment).
• Then stick tags on the wiring terminals (so as not to mix them up during assembly) that fit the devices and disconnect them.
• Next, unscrew the fasteners that secure the steering column to the dashboard, after which it will lie freely on the driver's seat.
• Then pull out the torpedo (you will need an assistant for this procedure), removing it from its place, carefully make sure that there are no unconnected terminals left, if any, they must be disconnected.
• And put the panel on something soft so as not to scratch it.
• Next, we disassemble the iron frame, which is located behind the removed torpedo, and also remove it together with an assistant.
• Then we disconnect the air ducts coming from the stove (it is better to mark or photograph them so as not to be confused during assembly).
• Now you can proceed to the "bifurcation" (unscrew the screws and remove the brackets).
• We get an electric motor with an impeller. Now you need to check it and understand whether the thing is repairable or not. In this case, it will be more convenient to replace the engine, since it is impossible to say exactly how long the repaired engine will last. And in case of failure, you will have to redo all the previous work.
• After repairing or replacing the motor, we assemble everything in the reverse order. And before the final assembly, we check its operation in all modes, and if everything works, then we complete the work.

These are the recommendations that can be given if the Gazelle Business stove motor does not work. Of course, it is unpleasant that because of such a trifle as an electric motor, you have to disassemble the entire torpedo, but without heat in the cabin it is inconvenient and unsafe to drive. Of course, you can contact the service, where it will be replaced and repaired. But if you have time and experience, you can do all the repairs yourself.

How to remove a gazelle stove fan business

In general, the stove asked for a long time, howled in waves, squealed in potholes, and then one fine day it began to howl constantly. it was decided to change it myself (a toad would have strangled 7 for a replacement), except that the engine shield would make some noise ... I decided to try to light it completely, uploading a bunch of videos and forums and did not find any data. The real problem was that it was very difficult to find a garage for such a crocodile, and stocking up on a 220v heater, I went to open it with spare parts to replace the stove motor ... I also bought: 4 sheets of STP AERO PREMIUM (enough 2,5) 2 sheets of BIPLAST A 15 (1,5 is enough)

Below is a picture with the location of the screws! Attention, you will need to remove: - Battery brand - Side grilles - Plastic with places for standard speakers - Side panel linings - Dashboard - Central part (xs as the name) between 4.5 and 6.7 - Lower glove box - Right cup holder - pull with a plastic screwdriver under the windshield glass (xs what is it called) ...

If all went well, open the hood and take a look

We unscrew, go into the salon, the panel should hang. It is required to unscrew the pipes from the stove radiator in the cabin

It is difficult to imagine a modern car without a cabin heater. This makes the journey not only comfortable, but also safe. When driving in the cold season, moisture condenses on cold windows and movement becomes difficult or even impossible. To prevent this from happening, hot air from the furnace is directed onto the glass, which heats them up and moisture does not condense on them.

 

Operating principle

The interior heating of the Gazelle Business, like many other cars, is carried out thanks to the heat generated by the car's engine. Heat in the engine is released during the combustion of fuel and friction surfaces. To remove heat from hot parts, a cooling system is built into the engine. It removes heat through the refrigerant. For interior heating, a heated liquid is used, which is supplied through pipes and lines to the radiator, due to which it heats up. To distribute heat throughout the passenger compartment, an electric motor with an impeller draws cold air through a heated radiator. After that, the heated air through the deflectors enters the cabin. By operating the dampers, you can direct the hot air to the right places. To control the air temperature, a heater tap is installed, with which you can adjust the amount of coolant passing through the radiator. A rheostat is installed to change the fan speed. All control is electronic. From the control unit, the signal goes to the gear motor, which, in turn, opens or closes the gate.

Diagnostics

Replacing the Gazelle stove motor Business is a very long and laborious process. And so that this work is not in vain, it is necessary to ensure its implementation.

1. With the engine off and the ignition on, turn the levers and check all modes. When switching, clicks of the operation of the gear motor should be heard. If no operation is heard, check the power supply of the control unit.
2. Next, you should try to change the position of the engine speed knob. If it does not work in all modes except the fastest, then the resistor is out of order. If there is no rotation in any of the positions, then it is necessary to check the power in the engine.
3. It is necessary to check the correctness of the heater radiator hoses: with a hot engine and a handle in hot air, they should be hot. If they are cold, then you need to check the faucet or actuator.

When the heater electric motor needs to be replaced

There are several signs that will tell the car owner that something is wrong with the heater motor. Here are the most common:

• When you try to melt the stove, the hum of the motor is not audible and this picture is observed at all three speeds.
• The engine supplies air at all speeds, but runs intermittently.
• The operation of the motor is stable, there are no interruptions in the supply of hot air, but instead of an even hum, strange sounds are heard - a rattling, which later turns into a piercing creak.
  

  Repair

  Having checked everything and with full confidence we can say that the faulty element is the stove motor, only after that you should proceed to disassemble the dashboard, since to remove the heater it is necessary to disassemble the entire torpedo assembly. For this operation, we need a set of heads and screwdrivers. To get to the heater, you need to disassemble the entire instrument panel.

  1. First of all, we will secure the workplace by disconnecting the positive cable from the battery.
  2. Remove the side plastic covers.
  3. Put speakers in the dashboard.
  4. Disconnect the instrument panel.
  5. Remove the left and right side covers.
  6. We unscrew the heater control unit with deflectors.

  

• Remove the deflector under the windshield.
• Unscrew and remove the glove box located below, on the passenger side.
• Next, unscrew the bolts that secure the heater to the car from the engine side.
• Drain the engine coolant into a clean container.
• Dismantle the pipes through which the engine coolant enters the heater radiator (there will be coolant residues in them, measures must be taken to prevent leakage of coolant into the passenger compartment).
• Then stick tags on the wiring terminals (so as not to mix them up during assembly) that fit the devices and disconnect them.
• Next, unscrew the fasteners that secure the steering column to the dashboard, after which it will lie freely on the driver's seat.
• Then pull out the torpedo (you will need an assistant for this procedure), removing it from its place, carefully make sure that there are no unconnected terminals left, if any, they must be disconnected.
• And put the panel on something soft so as not to scratch it.
• Next, we disassemble the iron frame, which is located behind the removed torpedo, and also remove it together with an assistant.
• Then we disconnect the air ducts coming from the stove (it is better to mark or photograph them so as not to be confused during assembly).
• Now you can proceed to the "bifurcation" (unscrew the screws and remove the brackets).
• We get an electric motor with an impeller. Now you need to check it and understand whether the thing is repairable or not. In this case, it will be more convenient to replace the engine, since it is impossible to say exactly how long the repaired engine will last. And in case of failure, you will have to redo all the previous work.
• After repairing or replacing the motor, we assemble everything in the reverse order. And before the final assembly, we check its operation in all modes, and if everything works, then we complete the work.

These are the recommendations that can be given if the Gazelle Business stove motor does not work. Of course, it is unpleasant that because of such a trifle as an electric motor, you have to disassemble the entire torpedo, but without heat in the cabin it is inconvenient and unsafe to drive. Of course, you can contact the service, where it will be replaced and repaired. But if you have time and experience, you can do all the repairs yourself.