Turning off the on-board computer - when required, methods
Content
Turning off the minibus will not affect the operation of the car in any way and, after completing this work, you will be able to use your car normally even without installing a new BC
The on-board computer (BC, bortovik, route computer, MK, minibus) helps the driver to monitor the operation of the car, and also monitors the main operational characteristics, for example, fuel consumption. But, in the event of a breakdown or when a more interesting model appears, the car owner has a question of how to turn off the on-board computer.
In what cases it is necessary to turn off the BC
The most common reason why it becomes necessary to disable the route is its incorrect operation, that is, it either does not function at all, or (does not show) some important information. After disconnecting the MK from the vehicle's on-board network, you can conduct a full check and establish the reason why it was buggy.
Another popular reason for turning off the on-board computer is the acquisition of a more modern and functional model. For example, instead of an outdated minibus with a minimum of functions, you can install an on-board vehicle with a satellite navigation module or a multimedia system.
It is also necessary to turn off the bortovik if, for some reason, it interferes, but it is impossible to replace or repair it at the moment. Therefore, so that the BC is not misleading, it is disconnected from the vehicle's on-board network. At the same time, the minibus itself remains in place so as not to spoil the interior of the cabin with a hole in the front panel.
What and how to do to disable
Theoretically, the answer to the question of how to turn off the on-board computer is very simple - just disconnect the corresponding wire blocks, after which the device can be removed from the “torpedo” or pulled out of its regular place.
Another problem is that at least half of the minibuses suitable for installation on a particular car model do not fully match its diagnostic connector and some of the sensors or actuators are connected by separate wires.
In this case, the simplest, but also the least reliable way is to install another one after the standard block, into which you can bring all the wires necessary for the operation of the on-board vehicle, which will allow you to quickly turn it off if necessary.
The disadvantage of this method is that an increase in the number of pads always leads to an increase in the probability of system failure due to oxidation of the contact surface caused by temperature condensation of moisture from the air. Therefore, to turn off the on-board computer, do this:
- disconnect the battery by removing the negative terminal from it;
- open access to the diagnostic connector through which the router is connected to the vehicle's on-board network;
- open the block;
- disconnect the wires that go to the BC bypassing the block;
- insulate the ends of these wires;
- attach them to the block and fasten with a plastic tie, so you will facilitate the installation of the device after repair or replacement.
There are no diagnostic connectors on carbureted machines, therefore, collect all the wires that fit the on-board computer into a pile and, having insulated their ends, fix them with a plastic tie.
How will the car behave after turning off the trip computer
Having dealt with the question of how to turn off the on-board computer, car owners immediately ask the following - will this affect the behavior of the car and is it possible to drive without a minibus. The on-board vehicle, even with the engine diagnostics function and the satellite navigation module, is only an additional device, therefore it does not interfere in any way with the operation of the main systems, such as preparing the air-fuel mixture or ignition.
Even those models that within a small range allow you to adjust the operation of the engine, for example, turning on the radiator cooling fan at a lower temperature, do not radically change the motor control system, so disabling such a device will return all settings to the base ones.
See also: Autonomous heater in a car: classification, how to install it yourself
That is, the engine will operate in the mode that is selected by the engineers of the plant that produced the vehicle, which means that it is optimal and does not pose any threat to the car. If you turn off the on-board computer with the GPS or GLONASS navigation function, this will also not affect the operation of the main vehicle systems, the only negative will be that the driver will not be able to use the navigator. Therefore, turning off the minibus will not affect the operation of the car in any way, and after doing this work, you will be able to use your car normally even without installing a new BC.
Conclusion
The on-board computer is a useful device that increases the driver's level of control over the car and makes the use of the car more comfortable. To turn off the minibus, it is enough to open the corresponding block and, if necessary, disconnect the wires of additional sensors and actuators.