Description of the P0348 fault code.
OBD2 Error Codes

P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2)

26.05.2022 /

P0348 – OBD-II Trouble Code Technical Description

Trouble code P0348 indicates that the PCM has detected too high voltage in the camshaft position sensor A (bank 2) circuit.

What does the fault code mean P0348?

Trouble code P0348 indicates that the engine control module (PCM) has detected excessive voltage on the camshaft position sensor "A" (bank 2) circuit. Other error codes related to the crankshaft and camshaft position sensors may also appear along with this code.

Fault code P0348

Possible reasons

Some possible reasons for the P0348 trouble code:

  • Defect or damage to the camshaft position sensor.
  • Problems with the wiring or connections in the camshaft position sensor circuit.
  • Incorrectly installed or damaged sensor connector.
  • Problems with the PCM (engine control module) or other engine management system components.
  • Incorrect voltage in the sensor power circuit caused by a short circuit or open circuit.
  • Problems with the vehicle's electrical system, such as breaks or short circuits in the wiring.

These are just a few of the possible causes, and for an accurate diagnosis it is necessary to inspect and test the relevant engine management system components.

What are the symptoms of a fault code?P0348?

Symptoms when trouble code P0348 is present may include the following:

  • The “Check Engine” indicator appears on the instrument panel.
  • Loss of engine power or sudden fluctuations in idle speed.
  • Abnormal engine operation, including noise, shaking, or unusual vibrations.
  • Problems with starting the engine or its unstable operation during a cold start.
  • Poor fuel economy or increased fuel consumption.
  • Automatic transmission shifting problems (if applicable).

However, the severity of symptoms may vary depending on the specific conditions and vehicle configuration.

How to diagnose a fault code P0348?

To diagnose DTC P0348, the following steps are recommended:

  1. Reading error codes: Use a diagnostic tool to read the error codes from the PCM ROM (Read Only Memory). Verify that the P0348 code is indeed present.
  2. Checking connections and wiring: Inspect the connections and wiring in the camshaft position sensor (bank 2) circuit. Make sure all connections are securely attached and that there is no visible damage or breaks in the wiring.
  3. Checking the camshaft position sensor: Check the camshaft position sensor itself for damage, corrosion, or shorts. Also check its resistance and voltage signals when the camshaft rotates.
  4. Checking the PCM and other components: Check the PCM and other engine management system components for defects or damage. This may require special equipment and knowledge.
  5. Checking the sensor signal: Use an oscilloscope or multimeter to check the camshaft position sensor signal. Make sure the signal meets the manufacturer's specifications.

If you are unable to diagnose the problem yourself, it is recommended that you contact a professional auto mechanic or auto repair shop for further diagnosis and repair.

Diagnostic errors

When diagnosing DTC P0348, the following errors may occur:

  • Incorrect interpretation of error code: Untrained technicians may misinterpret the P0348 code, which can lead to incorrect conclusions and incorrect repairs.
  • Insufficient diagnosis: The error can be caused not only by the camshaft position sensor itself, but also by other factors such as problems with the wiring, PCM or other engine management system components. Insufficient diagnostics can lead to replacement of unnecessary parts and additional costs.
  • Improper repair: If the cause of the error is not accurately determined, repair actions may be misdirected, which will not solve the problem and may cause the error code to reappear.
  • Ignoring other error codes: If there are multiple error codes associated with the crankshaft and camshaft position sensors, an error may occur if other error codes are ignored that may also affect engine performance.
  • Need for special equipment: To accurately diagnose and correct the problem, special equipment may be required, available only at specialized car repair centers or dealerships. Failure to ensure that the necessary equipment is available can complicate the diagnostic process.

To avoid these errors, it is recommended to contact qualified auto mechanics or specialized auto repair shops who have experience in diagnosing and repairing engine control systems.

How serious is the fault code? P0348?

The severity of the P0348 trouble code depends on several factors:

  • Influence on engine performance: If the camshaft position sensor (bank 2) is not functioning properly, engine performance may be adversely affected. Improper fuel and ignition timing management can result in reduced engine performance, poor fuel economy, and even long-term engine damage.
  • Potential engine damage: Improper functioning of the camshaft position sensor can result in uneven ignition or improper fuel injection, which in turn can cause undesirable engine conditions such as knocking, and wear of engine parts.
  • Impact on emissions: Improper engine management can also lead to increased emissions, which can affect the vehicle's environmental performance.

Overall, a P0348 code should be considered serious as it can negatively impact both engine performance and longevity, as well as the vehicle's environmental performance.

What repair will help eliminate the code? P0348?

To resolve the P0348 code, you must perform the following repair steps:

  1. Checking the camshaft position sensor: First check the condition of the sensor itself and its connections. If the sensor is damaged or its connections are faulty, it must be replaced or repaired.
  2. Electrical circuit check: Check the wires and connectors connecting the sensor to the engine control module. Make sure there are no breaks, corrosion or other damage.
  3. Checking the Engine Control Module (PCM): If all the previous steps do not resolve the problem, there may be a problem with the PCM itself. Check its operation or replace if necessary.
  4. Programming or updating PCM software: Sometimes problems can occur due to incorrect PCM program. In this case, updating the PCM software may help resolve the problem.
  5. Other possible repairs: If other problems are found, such as improper fuel delivery or incorrect ignition timing, these should also be corrected.

After completing these steps, it is recommended that you retest to ensure that the problem is resolved and that the P0348 code no longer appears.

How to Fix P0348 Engine Code in 3 Minutes [2 DIY Methods / Only $9.76]

P0348 – Brand-specific information

Trouble code P0348 usually refers to the camshaft position sensor and can occur in various makes of cars, a list of some brands of cars with explanations of P0348 codes:

These are just a few examples, and the causes and meanings of the P0348 code may vary depending on the specific model and year of the vehicle. If you are experiencing code P0348, it is recommended that you consult the repair manual for your specific vehicle make and model for more specific information about the causes and how to resolve this problem.

Add a comment