Description of the P0903 fault code.
OBD2 Error Codes

P0903 Clutch actuator circuit high

26.05.2022 /

P0903 – OBD-II Trouble Code Technical Description

Trouble code P0903 indicates a high signal in the clutch actuator circuit.

What does the fault code mean P0903?

Trouble code P0903 indicates a high signal in the clutch actuator circuit. This means that the transmission or engine control module has detected that the voltage in the clutch actuator control circuit is higher than normal. When the control module (TCM) detects high voltage or resistance in the clutch actuator circuit, code P0903 is set and the check engine light or transmission check light comes on.

Description of the P0903 fault code.

Possible reasons

Possible causes for DTC P0903:

  • Damage or corrosion of the wiring in the clutch control circuit.
  • Loose connection or break in the electrical connection.
  • The engine control module (PCM) or transmission control module (TCM) is faulty.
  • Problems with the sensor or sensor that controls the clutch drive.
  • Poor quality or incorrect installation of wiring.
  • Electrical noise or short circuit in the control circuit.

What are the symptoms of a fault code? P0903?

Symptoms for DTC P0903 may include the following:

  • The Check Engine light or transmission light on the instrument panel comes on.
  • Gear shifting problems such as hesitation or jerking.
  • Loss of engine power.
  • Unusual sounds or vibrations when shifting gears.
  • Vehicle failure to shift into certain gears or problems changing gears.

How to diagnose a fault code P0903?

The following steps are recommended to diagnose DTC P0903:

  1. Checking indicator lamps: Check to see if the Check Engine or Transmission indicator lights on the instrument panel come on when the ignition is turned on.
  2. Using an OBD-II Scanner: Connect the OBD-II scanner to your vehicle's diagnostic socket and read the trouble codes. Write down the P0903 code and any other codes that may be stored.
  3. Checking electrical connections: Check the electrical connections and wires in the clutch control circuit for damage, corrosion or breaks.
  4. Checking sensors: Check the condition of the sensors associated with the clutch actuator for correct installation, damage or wear.
  5. Checking Circuit Resistance: Measure the clutch control circuit resistance and compare it to the manufacturer's recommended values.
  6. Checking the transmission control module: If necessary, test the Transmission Control Module (TCM) for faults.
  7. Checking Electrical Components: Check the condition of electrical components such as fuses and relays that may affect the clutch control circuit.
  8. Rechecking fault codes: After performing any repairs, read the trouble codes again using the OBD-II scanner and ensure that the P0903 code is no longer active.

If the problem persists after following these steps, it is recommended that you contact a qualified auto mechanic or auto repair shop for more detailed diagnosis and repair.

Diagnostic errors

When diagnosing DTC P0903, the following errors may occur:

  • Incorrect interpretation of code: Some mechanics may misinterpret the P0903 code as a clutch actuator problem, when in fact the cause may be something else.
  • Skipping diagnostic steps: Incorrect order or skipping certain steps in diagnosis may result in missing the cause of the problem.
  • Incorrect replacement of parts: Replacing parts without proper diagnosis may result in unnecessary costs and may not solve the underlying problem.
  • Ignoring other fault codes: The P0903 code may be associated with other trouble codes, and ignoring them may result in an incomplete diagnosis.
  • Wrong solution to the problem: In some cases, mechanics may provide the wrong solution to a problem, which may result in continued symptoms or damage to other vehicle components.

To avoid these mistakes, it is important to follow the vehicle manufacturer's recommendations and perform diagnostics systematically, step by step, and use quality scanners and diagnostic tools.

How serious is the fault code? P0903?

Trouble code P0903 indicates a high signal level in the clutch actuator circuit, which may indicate a serious problem with the clutch actuator control system. Depending on the specific cause and operating conditions of the vehicle, this code may have varying severity.

For example, if the high signal level is caused by a short circuit or open circuit in the clutch control circuit, this can lead to complete inoperability of the transmission and the inability to shift gears. This may cause a breakdown or accident, so the P0903 code should be considered serious in such cases.

However, if the high signal level is caused by less critical problems, such as improper sensor configuration or electrical failure, then the impact on vehicle safety and performance may be less severe.

In any case, the P0903 code requires serious attention and should be corrected as soon as possible, especially if it is accompanied by other symptoms such as abnormal transmission behavior or indicator lights on the dashboard.

What repair will help eliminate the code? P0903?

The repairs needed to resolve the P0903 code will depend on the specific cause of the code, but here are some general guidelines:

  1. Electrical circuit check: First, you should diagnose the electrical clutch control circuit. This includes checking the wiring for breaks, shorts, and other electrical problems.
  2. Checking the clutch sensor: The clutch actuator sensor may be damaged or misconfigured, which can cause a high signal in the circuit. In this case, the sensor must be replaced or adjusted.
  3. Checking the Transmission Control Module (TCM): If all electrical components are normal, the problem may be with the TCM. Diagnose the TCM for errors and operation.
  4. Repair or replacement of components: Depending on the diagnostic result, it may be necessary to repair or replace individual components of the clutch control system, such as sensors, wiring, relays, etc.
  5. Firmware or reprogramming: Sometimes problems with error codes can be related to the TCM software. In this case, the TCM may need to be flashed or reprogrammed.

It is recommended that you contact a qualified mechanic or auto repair shop for diagnosis and repair. It is important to accurately determine the cause of the P0903 code to prevent the problem from occurring again.

How to Diagnose and Fix P0903 Engine Code - OBD II Trouble Code Explain

P0903 – Brand specific information

Trouble code P0902 can apply to various makes and models of vehicles, the definition of P0902 code for some well-known manufacturers:

These are general definitions only, and specific terms and meanings may vary slightly depending on the specific model and year of the vehicle. For accurate information, it is recommended to consult the repair manual or service specialists for your specific vehicle brand.

Add a comment