Fuses and relay boxes for the BMW 1 Series
Content
Fuse box diagram (fuse location), location and function of fuses and relays BMW 1 series (E81, E82, E87, E88; 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013) 116i , 116d, 118i, 118d, 120i, 120d, 123d, 125i, 130i, 135i, M1.
Checking and replacing fuses
The electrical circuits of the car are protected from short circuits by fuses. This greatly reduces the chance of damage due to electrical problems.
To check the fuse, look at the silver strip inside the fuse. If the tape is torn or melted, replace the fuse. Be sure to replace the defective fuse with a new one of the same size and rating.
Fuses of the same amperage can be temporarily taken elsewhere if the fuse is blown. Replace the fuse as soon as possible.
Note
- Before replacing a fuse, make sure the key is removed from the ignition and all communications are turned off and/or disconnected.
- When replacing a blown fuse, it is important to use only a fuse with the correct current rating. Use of a fuse with a different rating than specified may result in a dangerous overload of the electrical system.
- If the correct rated fuse continues to blow, this indicates a circuit problem that needs to be corrected.
Fuse box in the glove box
Access to the fuse box
To get access:
- Open the glove box.
- Remove the shock absorber from the carriage by sliding it forward.
- Separate the glove box by pressing both latches and folding it.
The plastic clips are located in the junction box. Information on the purpose of the fuses can be found next to the junction box. Replacement fuses are available from your BMW Centre. After replacing the fuse, lift the glove box until it clicks into place and reinstall the damper.
Advertising!
Never attempt to repair a blown fuse or replace a defective fuse with a fuse of a different color or amperage; otherwise, it may overload the circuit, eventually causing the car to catch fire.
Fuse block diagram
Ads
number | BUT | Protected circuits |
---|---|---|
F1 | fifteen | up to 09.2005: gearbox control |
ten | as of 09.2006: Rollover protection controller | |
F2 | 5 | up to 03.2007: electrochromic interior mirror |
as of 03.2007: | ||
Instrument cluster control unit | ||
obdi connector | ||
F3 | — | — |
F4 | 5 | Car access system |
F5 | 7,5 | up to 03.2007: Function control center, roof |
twenty | as of 03.2007: electric fuel pump | |
F6 | fifteen | up to 09.2007: gearbox control unit |
5 | as of 09.2007: | |
ABC sensor | ||
DC/DC converter | ||
F7 | twenty | up to 03.2007: auxiliary/auxiliary heater control unit |
F8 | 5 | until 03.2007: CD changer |
twenty | as of 03.2007: Amplifier | |
F9 | ten | up to 03.2007: active cruise control |
F10 | — | — |
F11 | ten | until 09.2007: Radio |
30 | as of 09.2007: | |
N52 (125i, 130i): | ||
Oil condition sensor | ||
Block DISA 1 | ||
DISA 2 units | ||
Fuel tank vent valve | ||
Crankshaft sensor | ||
Air mass sensor | ||
twenty | as of 09.2007: | |
N46/TU2 (118i, 120i), N45/TU2 (116i): | ||
Nozzle cylinder 1 | ||
Cylinder nozzle 2 | ||
Cylinder nozzle 3 | ||
Cylinder nozzle 4 | ||
N43 (116i, 118i, 120i): | ||
Oxygen sensor before catalytic converter | ||
Oxygen sensor 2 before catalytic converter | ||
Oxygen sensor after catalytic converter | ||
F12 | twenty | up to 09.2007: Function control center, roof |
fifteen | as of 09.2007: Vacuum pump relay | |
F13 | 5 | Controller |
F14 | — | — |
F15 | 5 | ABC sensor |
F16 | fifteen | before 03.2007: right horn |
03.2007-09.2007: | ||
Left horn | ||
right horn | ||
ten | as of 09.2007: | |
N46/TU2 (118i, 120i), N45/TU2 (116i): | ||
Electronic box fan | ||
Crankshaft sensor | ||
Fuel tank vent valve | ||
Hot film air mass meter | ||
N43 (116i, 118i, 120i): | ||
Electronic box fan | ||
Crankshaft sensor | ||
Variable intake system: position sensor and actuator | ||
Air mass sensor | ||
Radiator damper actuator | ||
N52 (125i, 130i): | ||
EAC-sensor | ||
Secondary air pump relay | ||
Electronic box fan | ||
F17 | 5 | up to 03.2007: Navigation system |
ten | as of 09.2007: | |
N52 (125i, 130i): | ||
exhaust damper | ||
USA: fuel tank leak diagnosis module. | ||
N43 (116i, 118i, 120i): | ||
Nitric oxide sensor | ||
F18 | 5 | until 03.2007: CD changer |
as of 03.2007: Electrochromic interior mirror | ||
F19 | 7,5 | until 03.2007: |
Comfort access control module | ||
Driver's door external handle electronic module | ||
Passenger Side Door Handle Electronic Module | ||
Siren and tilt sensor | ||
as of 03.2007: siren and tilt sensor | ||
F20 | 5 | Dynamic Stability Control (DSC) |
F21 | 7,5 | Driver's door central switch |
Outside mirrors | ||
F22 | — | — |
F23 | ten | without USA: |
Digital tuner | ||
Video module | ||
UNITED STATES: | ||
Satellite receiver | ||
American digital tuner | ||
F24 | 5 | Tire pressure monitoring (RDC) |
F25 | — | — |
F26 | ten | Telematics control unit (TCU) |
Universal Charger and Hands Free (ULF) | ||
Telephone transceiver (without TCU or ULF) | ||
Antenna splitter | ||
Compensator | ||
extraction box | ||
F27 | 5 | Driver's door central switch |
Telephone transceiver | ||
F28 | 5 | Function control center, roof |
Remote Parking Control (PDC) | ||
F29 | 5 | AUC sensor (until 03.2007) |
Driver seat heating module | ||
Passenger seat heating module | ||
F30 | twenty | Front cigarette lighter |
Charging socket at the rear of the center console | ||
Socket in the trunk | ||
F31 | 30 | up to 09.2005: Dynamic Stability Control (DSC) |
twenty | as of 09.2005: | |
Radio (with RAD Radio or RAD2-BO user interface) | ||
CCC / M-ASK (with M-ASK-BO user interface or CCC-BO user interface) | ||
F32 | 30 | until 03.2007: |
Left front seat module (with memory) | ||
Driver seat heating module (no memory) | ||
as of 03.2007: Seat module front left | ||
F33 | 30 | until 03.2007: |
Switch, passenger seat adjustment | ||
Passenger seat back width adjustment switch | ||
Passenger lumbar switch | ||
Passenger seat back width adjustment valve block | ||
Lumbar support valve block, front right | ||
5 | as of 03.2007: | |
Comfort access control unit | ||
Driver's door external handle electronic module | ||
Passenger Side Door Handle Electronic Module | ||
F34 | 30 | up to 03.2007: Amplifier |
5 | with 03.2007: CD changer | |
F35 | twenty | until 09.2005: |
N46 (118i, 120i), N45 (116i): | ||
Electric fuel pump | ||
N52 (125i, 130i), M47/TU2 (118d, 120d): | ||
Fuel pump control (EKPS) | ||
30 | as of 09.2005: Dynamic Stability Control (DSC) | |
F36 | 30 | Footwell module |
F37 | 30 | until 03.2007: |
Driver seat back width adjustment switch | ||
Driver's lumbar switch | ||
Driver seat back width adjustment valve block | ||
Lumbar support valve block front left | ||
ten | 03.2007-09.2007: | |
Passenger seat back width adjustment switch | ||
Driver seat back width adjustment switch | ||
Passenger lumbar switch | ||
Driver's lumbar switch | ||
Driver seat back width adjustment valve block | ||
Driver seat back width adjustment valve block | ||
Lumbar support valve block front left | ||
Lumbar support valve block front left | ||
30 | as of 09.2007: | |
N52 (125i, 130i): | ||
DME control unit | ||
Electric coolant pump | ||
Thermostat, card cooling function | ||
Intake camshaft position sensor | ||
Exhaust camshaft sensor | ||
VANOS solenoid valve, inlet | ||
VANOS solenoid valve, output | ||
F38 | 30 | as of 09.2007: |
N52 (125i, 130i): | ||
Oxygen sensor before catalytic converter | ||
Oxygen sensor 2 before catalytic converter | ||
Oxygen sensor after catalytic converter | ||
Oxygen sensor 2 after catalytic converter | ||
Heated crankshaft breather 1 | ||
F39 | 30 | up to 09.2007: wiper motor |
as of 09.2007: | ||
N52 (125i, 130i): | ||
Nozzle cylinder 1 | ||
Cylinder nozzle 2 | ||
Cylinder nozzle 3 | ||
Cylinder nozzle 4 | ||
Cylinder nozzle 5 | ||
Cylinder nozzle 6 | ||
Ignition coil 1 cylinder | ||
Ignition coil 2 cylinder | ||
Ignition coil 3 cylinder | ||
Ignition coil 4 cylinder | ||
Ignition coil 5 cylinder | ||
Ignition coil 6 cylinder | ||
Interference suppression capacitor for ignition coils | ||
F40 | twenty | until 09.2005: |
Radio (with RAD Radio or RAD2-BO user interface) | ||
CCC / M-ASK (with M-ASK-BO user interface or CCC-BO user interface) | ||
from 09.2005 to 03.2007: | ||
Electric fuel pump (without EKPS) | ||
Fuel pump control (EKPS) | ||
7,5 | as of 03.2007: Function control center, roof | |
F41 | 30 | Footwell module |
F42 | 30 | until 09.2005: |
Driver seat back width adjustment switch | ||
Driver's lumbar switch | ||
Driver seat back width adjustment valve block | ||
Lumbar support valve block front left | ||
09.2006-03.2007: Trailer module | ||
40 | as of 03.2007: Footwell module | |
F43 | 30 | Headlight washer pump |
F44 | 30 | Trailer module |
F45 | twenty | up to 09.2005: trailer socket |
40 | 09.2005-03.2007: Current address. | |
30 | as of 03.2007: Seat module front right | |
F46 | 30 | Rear defroster interlock circuit (positive) |
F47 | twenty | as of 09.2005: Trailer socket |
F48 | twenty | Rear wiper/washer intermittent control unit |
F49 | 30 | up to 03.2007: Passenger seat heating module |
03.2007-09.2007: Front Right Seat Module | ||
40 | as of 09.2007: current address | |
F50 | 40 | up to 09.2005: Active control. |
ten | as of 03.2007: DME control unit | |
F51 | 50 | Car access system |
F52 | 50 | up to 03.2007: footwell module |
twenty | as of 03.2007: Driver seat heating module | |
F53 | 50 | up to 03.2007: footwell module |
twenty | as of 03.2007: Passenger seat heating module | |
F54 | 60 | until 03.2007: B + potential distributor |
30 | from 03.2007: trailer module | |
F55 | — | — |
F56 | fifteen | central locking |
F57 | fifteen | central locking |
F58 | 5 | Dashboard |
obdi connector | ||
F59 | 5 | Shift center in steering column |
F60 | 7,5 | Heating / air conditioning system |
F61 | ten | Central information display |
Glove box lighting | ||
Luggage compartment lighting, right | ||
F62 | 30 | Window control |
F63 | 30 | Window control |
F64 | 30 | Window control |
F65 | 40 | Dynamic Stability Control (DSC) |
F66 | 50 | Fuel heater |
F67 | 50 | up to 03.2007: fan output stage |
30 | as of 03.2007: Fan output stage | |
F68 | 50 | up to 03.2007: vacuum pump electrical relay |
40 | as of 03.2007: Footwell module | |
F69 | 50 | Electric fan |
F70 | 50 | secondary air pump |
N45 (116i): | ||
Electric vacuum pump | ||
F71 | twenty | Jack |
F72 | fifteen | N45, N45/TU2 (116i): |
Relay, electric pump | ||
F73 | ten | N46/TU2 (118i, 120i), N45/TU2 (116i): |
Crankshaft sensor | ||
Electronic box fan | ||
Fuel tank vent valve | ||
Hot film air mass meter | ||
03.2007-09.2007: | ||
N52 (125i, 130i): | ||
EAC-sensor | ||
Secondary air pump relay | ||
Electronic box fan | ||
Hot film air mass meter | ||
F74 | ten | 03.2007-09.2007: |
N52 (125i, 130i): | ||
exhaust damper | ||
USA: fuel tank leak diagnosis module. | ||
as of 09.2007: | ||
N43 (116i, 118i, 120i): | ||
Nitric oxide sensor | ||
F75 | — | — |
F76 | twenty | 03.2007-09.2007: |
N43 (116i, 118i, 120i): | ||
Oxygen sensor before catalytic converter | ||
Oxygen sensor 2 before catalytic converter | ||
Oxygen sensor after catalytic converter | ||
N46/TU2 (118i, 120i), N45/TU2 (116i): | ||
Nozzle cylinder 1 | ||
Cylinder nozzle 2 | ||
Cylinder nozzle 3 | ||
Cylinder nozzle 4 | ||
30 | 03.2007-09.2007: | |
N52 (125i, 130i): | ||
Oil condition sensor | ||
Block DISA 1 | ||
DISA 2 units | ||
Fuel tank vent valve | ||
Crankshaft sensor | ||
Air mass sensor | ||
F77 | 30 | N43 (116i, 118i, 120i): |
DME control unit | ||
Oil pressure control valve | ||
Intake camshaft position sensor | ||
Exhaust camshaft sensor | ||
VANOS solenoid valve, inlet | ||
VANOS solenoid valve, output | ||
N45/TU2 (116i): | ||
DME control unit | ||
Suction Jet Pump Valve | ||
Intake camshaft position sensor | ||
Exhaust camshaft sensor | ||
VANOS solenoid valve, inlet | ||
VANOS solenoid valve, output | ||
Heating, crankcase ventilation | ||
N46/TU2 (118i, 120i): | ||
DME control unit | ||
Thermostat card | ||
Intake camshaft position sensor | ||
Exhaust camshaft sensor | ||
VANOS solenoid valve, inlet | ||
VANOS solenoid valve, output | ||
Heating, crankcase ventilation | ||
03.2007-09.2007: | ||
N52 (125i, 130i): | ||
Nozzle cylinder 1 | ||
Cylinder nozzle 2 | ||
Cylinder nozzle 3 | ||
Cylinder nozzle 4 | ||
Cylinder nozzle 5 | ||
Cylinder nozzle 6 | ||
Ignition coil 1 cylinder | ||
Ignition coil 2 cylinder | ||
Ignition coil 3 cylinder | ||
Ignition coil 4 cylinder | ||
Ignition coil 5 cylinder | ||
Ignition coil 6 cylinder | ||
Interference suppression capacitor for ignition coils | ||
F78 | 30 | N43 (116i, 118i, 120i): |
Ignition coil 2 cylinder | ||
Ignition coil 3 cylinder | ||
Ignition coil 4 cylinder | ||
Interference suppression capacitor for ignition coils | ||
N46/TU2 (118i, 120i), N45/TU2 (116i): | ||
Oxygen sensor before catalytic converter | ||
Oxygen sensor 2 before catalytic converter | ||
Oxygen sensor after catalytic converter | ||
03.2007-09.2007: | ||
N52 (125i, 130i): | ||
DME control unit | ||
Electric coolant pump | ||
Thermostat, card cooling function | ||
Intake camshaft position sensor | ||
Exhaust camshaft sensor | ||
VANOS solenoid valve, inlet | ||
VANOS solenoid valve, output | ||
F79 | 30 | 03.2007-09.2007: |
N43 (116i, 118i, 120i): | ||
Oil condition sensor | ||
Heating, crankcase ventilation | ||
Electric reversing valve, motor support | ||
Fuel tank vent valve | ||
Volume control valve | ||
Thermostat card | ||
N46/TU2 (118i, 120i), N45/TU2 (116i): | ||
Ignition coil 1 cylinder | ||
Ignition coil 2 cylinder | ||
Ignition coil 3 cylinder | ||
Ignition coil 4 cylinder | ||
N52 (125i, 130i): | ||
Oxygen sensor before catalytic converter | ||
Oxygen sensor 2 before catalytic converter | ||
Oxygen sensor after catalytic converter | ||
Oxygen sensor 2 after catalytic converter | ||
Heated crankshaft breather 1 | ||
F80 | — | — |
F81 | 30 | Trailer module |
F82 | — | — |
F83 | — | — |
F84 | 30 | Headlight washer pump |
F85 | — | — |
F86 | — | — |
F87 | — | — |
F88 | twenty | up to 09.2007: Fuel pump control (EKPS) |
30 | as of 09.2007: Fan output stage |
Relay
number | Explanation |
---|---|
one | Wiring Harness Connector |
two | A dual electric fuel pump relay/trumpet horn (M47TU2 only) is mounted on the housing board. |
3 | Finished. Relay 30g_f (installed only together with the corresponding equipment) is mounted on the board in the housing |
4 | Finished. Relay 15 installed in a housing on the dashboard |
5 | Finished relay 30g |
6 | Source of power |
7 | Windshield washer relay |
eight | Secondary air pump relay |
nine | Internal interface, junction box control unit |
ten | Rear Wiper Relay |
11 | Heated rear window relay |
12 | Wiper Stage 1 Relay |
thirteen | The 2nd stage wiper relay is installed on the circuit board in the housing. |