Slot box for subwoofer Ural TT 12 with port setting 35 hz
Content
The Ural Sound subwoofer of the TT 12 series has a reinforced basket, overload-resistant 3-inch (76.2 mm) coil with a winding height of 30 mm on an aluminum frame with an increased section. For this subwoofer, we calculated a slotted box at 35 hz.
The net volume is 50 liters, which is not much for a subwoofer with a diameter of 12. As a result, a compact box with good speed and the ability to win back bass from 30 hz is obtained.
Box detailing
A small number and a simple shape of the subwoofer cabinet parts make it possible to make them in a home workshop or order them at any furniture company. In the first case, you can be proud of your skill, and in the second, save time and nerves. It should be noted right away that the most important parameter that should be paid attention to is the solidity, structural strength and tightness of all subwoofer connections, this is much more important than appearance.
The dimensions of the parts are as follows:
| number | the name of detail | Dimensions (MM) | PCS |
|---|---|---|---|
| 1 | Front and back walls | X 340 606 | 2 |
| 2 | Right wall | X 340 350 | 1 |
| 3 | Left wall | X 340 303 | 1 |
| 4 | Bass reflex wall 1 | X 340 523 | 1 |
| 5 | Bass reflex wall 2 | X 340 91 | 1 |
| 6 | Lid and bottom | X 606 386 | 2 |
| 7 | Rounds (Both sides at 45°) | X 340 45 | 4 |
Characteristics of the box
| 1. | subwoofer speaker | Ural TT 12 |
|---|---|---|
| 2. | Box setting | 35 Hz |
| 3. | net volume | 50 l |
| 4. | Overall volume | 67.8 l |
| 5. | Port area | 160 cc |
| 6. | Port length | 65.29 см |
| 7. | Material thickness | 18 mm |
| 8. | Under what body the calculation was made | Sedan |
Recommended Amplifier Settings
We understand that a large number of people visiting our portal are non-professionals, and they are worried that if they are configured and used incorrectly, they can render the entire system unusable. To save you from fears, we have made a table with recommended settings for this calculation. Find out what wattage rating (RMS) your amplifier has and set the settings as recommended. I would like to note that the settings indicated in the table are not a panacea, and are advisory in nature.
| Setting name | RMS 300-400w | RMS 400-600w | RMS 600-800w |
|---|---|---|---|
| 1. GAIN (lvl) | 60-80% | 55-75% | 45-70% |
| 2. Subsonic | 27 Hz | 27 Hz | 27 Hz |
| 3. Bass Boost | 0-50% | 0-25% | 0-15% |
| 4.LPF | 50-100hz | 50-100hz | 50-100hz |
*PHASE - smooth phase adjustment. There is such an effect as the subwoofer bass is temporarily behind the rest of the music. However, by adjusting the phase, this phenomenon can be reduced.
Before installing the amplifier, read the instructions, in it you will find what cross-section of the power wire is necessary for the stable operation of your amplifier, use only copper wires, monitor the reliability of the contacts, as well as the voltage of the on-board network. Here we have described in detail how to connect the amplifier.
box frequency response
AFC - graph of the amplitude-frequency characteristic. It clearly demonstrates the dependence of loudness (dB) on the frequency of sound (Hz). From which you can imagine how our calculation will sound, installed in a car with a sedan body.
Conclusion
We have put a lot of effort into creating this article, trying to write it in a simple and understandable language. But it is up to you to decide if we did it or not. If you still have questions, create a topic on the "Forum", we and our friendly community will discuss all the details and find the best answer to it.
And finally, do you want to help the project? Subscribe to our Facebook community.
