
U0229 Lost Communication With Heated Steering Wheel Module
Content
U0229 Lost Communication With Heated Steering Wheel Module
OBD-II DTC Datasheet
Lost Communication With Heated Steering Wheel Module
What does this mean?
This is a generic communications system diagnostic trouble code that applies to most makes and models of OBD-II vehicles.
This code means the heated steering wheel module (HSWM) and other control modules on the vehicle are not communicating with each other. The circuitry most commonly used for communication is known as Controller Area Bus communication, or simply the CAN bus.
Modules communicate with each other over a network, just like the network you have at home or work. Car manufacturers use several networked systems. Prior to 2004, the most common (non-exhaustive) inter-module communication systems were the serial communication interface, or SCI; SAE J1850 or PCI bus; and Chrysler Collision Detection, or CCD. The most common system used after 2004 is known as Controller Area Network communication, or simply the CAN bus (also used until 2004 on a small segment of vehicles). Without this CAN bus, control modules cannot communicate and your scan tool may or may not receive information from the vehicle, depending on which circuit is affected.
The Heated Steering Wheel Module (HSWM) is usually located inside the steering column. It receives input from a variety of sensors, some of which are directly connected to it, and most are transmitted over a bus communication system from the powertrain control module (PCM). These inputs allow the module to control a heating element inside the steering wheel.
Troubleshooting steps may vary depending on the manufacturer, the type of communication system, the number of wires, and the colors of the wires in the communication system.
Code severity and symptoms
The seriousness in this case is never serious, as this is a device for the convenience of customers, and in the event of a complete power failure, there is always a manual workaround. The absence of HSWM operation does not in any way affect the operation of the vehicle.
Symptoms of a U0229 code may include:
- The rudder element does not heat up (turns on)
- Steering wheel heating is always on
- HSWM won't turn on / doesn't work
reasons
Usually the reason for installing this code is:
- Open circuit on CAN bus + or - circuit
- Short to ground or ground in any CAN bus circuit
- No power or ground to HSWM module
- Rarely - the control module is faulty
Diagnostic and repair procedures
A good place to start with ALL electrical diagnostics is to check the Technical Service Bulletins (TSB) for your vehicle. The problem you are facing may be known to others in the field. A known fix may have been released by the manufacturer and can save you time and money during diagnostics.
It is assumed that you have access to a code reader at this point, as you may have been able to access the codes up until now. See if there were any other DTCs related to bus communication or battery / ignition. If so, you should diagnose them first, as misdiagnosis is known to occur if you diagnose the U0229 code before any of the underlying codes are thoroughly diagnosed and corrected.
If the only code you get from other modules is U0229, try accessing HSWM. If you can access codes from HSWM, then the U0229 code is either intermittent or a memory code. If you can't access HSWM, then the U0229 code set by other modules is active and the problem already exists.
The most common failure is a circuit fault that results in no power or ground to the heated steering wheel module.
Check all fuses supplying the HSWM on this vehicle. Check out all the reasons for HSWM. Locate ground anchorage points on the vehicle and make sure these connections are clean and secure. If necessary, remove them, take a small wire bristle brush and baking soda / water solution and clean each one, both the connector and the place where it connects.
If any repairs have been made, clear the diagnostic trouble codes from any modules that set the code in memory and see if you can now communicate with the HSWM module. If communication with the HSWM recovers, the problem is most likely a fuse / connection issue.
If the code returns or communication with the module still fails, locate the CAN bus communication connections on your vehicle, primarily the HSWM connector, which is usually located inside the steering column. Disconnect the negative battery cable before disconnecting the connector from the HSWM. Once detected, visually inspect the connectors and wiring. Look for scratches, scuffs, exposed wires, burn marks, or molten plastic.
Disconnect the connectors and carefully inspect the terminals (metal parts) inside the connectors. See if they look burnt or have a green tint indicating corrosion. If you need to clean the terminals, use an electrical contact cleaner and a plastic bristle brush. Allow to dry and apply electrical grease where the terminals touch.
Before connecting the connectors back to the HSWM, perform these few voltage checks. You will need access to a digital volt ohm meter (DVOM). Make sure the HSWM has power and ground. Access the wiring diagram and determine where the main power and ground connections enter the HSWM. Connect the battery before continuing, with the HSWM disconnected. Connect the red lead of your volt meter to each B+ (battery voltage) supply entering the HSWM connector, and the black lead of your volt meter to a good ground (if unsure, the negative post of the battery always works). You should see a battery voltage reading. Make sure you have a good ground. Connect the red lead of your volt meter to the battery positive (B+) and the black lead to each ground circuit. Once again, you should see battery voltage with each connection. If not, troubleshoot the power or ground circuit.
Next, check the two communication circuits. Find the CAN C+ (or HSCAN+) circuit and the CAN C- (or HSCAN – circuit). With the black lead of the voltmeter connected to a good ground, connect the red lead to CAN C+. With the key on and the engine off, you should see about 2.6 volts with a little oscillation. Then connect the red lead of the voltmeter to the CAN C- circuit. You should see about 2.4 volts with a little oscillation. Other manufacturers show CAN C- at about 5 volts and a oscillating key with the engine off. Check your manufacturer's specifications.
If all tests pass and communication is still not possible, or you have not been able to reset the U0229 trouble code, the only thing to do is to seek help from a trained automotive diagnostician, as this would indicate a HSWM failure. Most of these HSWMs need to be programmed or calibrated to properly install the vehicle.
Related DTC discussions
- There are currently no related topics in our forums. Post a new topic on the forum now.
Need more help with the U0229 code?
If you still need help with DTC U0229, post a question in the comments below this article.
NOTE. This information is provided for informational purposes only. It is not intended to be used as a repair recommendation and we are not responsible for any action you take on any vehicle. All information on this site is protected by copyright.

