We remove tinting and glue from it from car glass - top effective ways
Content
Window tinting is present on many cars today. However, in order to avoid unpleasant situations with traffic police officers, the tint film must be applied in accordance with acceptable standards. If this is not the case, then sooner or later it will have to be removed or replaced. You can remove the old film from car glass with your own hands in a garage without visiting a specialized service.
Permissible norms for tinting car windows in 2019
In January 2019, a new tinting law came into force to improve road safety. The main emphasis is on increasing the fine for non-compliance with glass light transmission standards from 500 rubles. up to 1,5 thousand rubles for the first violation and up to 5 thousand rubles. for a repeat. On a car, it is allowed to use materials whose light transmission does not contradict the following rules (GOST 32565–2013):
- light transmission of the windshield 75%;
- front side windows - 70%;
- for rear windows is not standardized;
- tint film should not distort white, red, green, blue and yellow colors;
- in the upper part of the windshield it is allowed to apply a darkening strip with a width of not more than 140 mm.
It is forbidden to use a mirror film as a dimming element.
How to remove tint from glass in different ways
The need to remove the tinting material may arise for a number of reasons:
- replacement of the film with a new one in case of formation of defects (bubbles, deformation);
- after buying a car, it may turn out that the tinting has a low light transmission;
- when cracks and chips appear on the glass, because they can spread further.
Film removal tips
In order for the removal of the tint film to be successful and not require a lot of time, it is advisable to adhere to the following recommendations:
- if the heating method is chosen, and the work is supposed to be carried out in winter, then the machine should be placed in a warm room in advance. Otherwise, there is a possibility of cracks on the glass due to temperature differences;
- during heating, do not allow the film to melt, since it will not be easy to remove it;
- for heating, it is better to give preference to an industrial hair dryer;
- when using a soapy solution to remove the film, protect the bottom of the glass with a rag to avoid accumulation of excess liquid;
- when using sharp objects, it is necessary to direct them to the glass at an acute angle;
- the use of abrasives should be avoided;
- the film must be separated after softening the adhesive layer;
- first you need to try to remove the tint with soapy water, and if it doesn’t work, then use solvents.
heating
If the tint film has been applied for a long time, then it will be more difficult to remove it. In this case, you will have to resort to heating with a building hair dryer or a steam generator. All nearby decorative elements will have to be dismantled.
During operation, avoid getting hot stream on rubber and plastic elements, as they can be deformed.
The withdrawal procedure consists of the following steps:
- Thoroughly heat the film from the removal side.
- We pry off the edges of the tinting with a knife or blade.Pry off the edge of the film with a knife or blade
- On the removed area, we maintain the temperature within +40 ° C and at the same time remove the film.Heat the film with a hair dryer
- After removing the tint, clean the glass from the remaining glue.
Video: removing tinted side windows
Without heating
To remove tinting without heating devices, you will need:
- sharp knife;
- dishwashing liquid;
- solvent;
- scraper;
- spray;
- rags.
The procedure is as follows:
- Carefully pry the film from above with a knife and pull it down.We pry the film and pull it down
- After removing every 5–10 cm of the material, we wet the surface with detergent from the sprayer.
- Having completely removed the tinting material, remove the remaining glue with a scraper.
- If there is glue or a film on the glass in some places that cannot be removed, remove them with a rag soaked in the solvent.
- When the surface is clean, wipe the glass dry.After cleaning the surface, wipe the glass
How to remove the tint from the rear window if heating is installed there
If your car has a heated rear window, then there may be some difficulty in removing the shading material. This is due to the fact that when removing the film, the conductive heating filaments can be damaged. To avoid trouble, tinting must be removed in compliance with the following rules:
- remove the film only by heating;
- do not make sudden movements;
- when removing glue residue, do not touch the areas where the threads are located with a rag.
Video: removing film from heated glass
Watch this video on YouTube
How and how to remove glue from tinting
You can remove the adhesive layer after removing the tinting material using various means, both prepared with your own hands and store-bought:
- Soap solution. A simple and inexpensive option, which is prepared from soap and water with the addition of a small amount of ammonia. Since soap has a low efficiency, this option is only suitable for removing a small amount of glue.
- White Spirit. The tool shows good results, but when working with it, you should be aware of its toxicity. In addition, do not allow it to get on decorative elements and seats.
- Spray KERRY. Its advantage is ease of use and high efficiency. Among the shortcomings, toxicity and price, which is at least 400 rubles, can be distinguished.
- Rust converter Star Wax. Can be applied by spraying. It is highly efficient and inexpensive - about 80 r.
- Super Moment Anticle. Able to remove any adhesive stains. It is characterized by ease of application on vertical surfaces. It costs about 150 rubles.
- Biosolvent Cytosol. Removes adhesive and bituminous stains. It is a non-toxic substance. However, finding it for sale is not so easy.
Consider the procedure for removing glue using a soap solution as an example. For this you need to prepare:
- spray;
- soap solution;
- building hair dryer;
- scratcher
The sequence of actions is as follows:
- We heat the surface with a hair dryer to +40 ° C and at the same time spray the cleaning solution.
- With a scraper at an angle of about 30 °, we clean off the adhesive layer.The adhesive layer is removed with a scraper
- In areas where the adhesive has not been removed, the solution is applied again. If a large amount of glue remains, then add a little ammonia to the cleanser.Re-apply the solution to the areas with glue
If other means are used to remove the adhesive composition, then work with them according to the instructions for use.
Video: how to remove glue from tinting
Watch this video on YouTube
Removing the tint film is easy. It is enough to follow the described recommendations and step-by-step actions, using a minimum set of tools. If the tinting is removed in a hurry, then after that it will take a lot of effort to remove the remnants of the darkening coating and the adhesive layer.