How to close the glass in the car if the window regulator is broken

To prevent malfunctions, mechanical components and parts of closing systems must be periodically lubricated.

Minor faults in the car sometimes cause a lot of trouble. Finding ways to close the glass in the car if the window regulator is broken is time consuming and stressful. To solve a problem, you need to know how to proceed.

How to close the window if the power window does not work

If the lifting mechanism has failed and there is no way to immediately contact the master, there are 2 ways out of the situation:

• repair yourself;
• find a temporary solution.

It is possible to close the glass in the car if the window regulator is broken, you can do it in a simple way.

Without opening the door

If the window is not completely sunken into the door, try this method:

1. Open the door.
2. Clamp the glass between your palms on the outside and inside.
3. Pull up gradually until it stops.

How to close the glass in the car with your hands

The probability of the glass returning to its original position depends on the nature of the failure of the lifting mechanism.

If the window is completely open, do the following:

1. Take a strong twine or fishing line.
2. From wire, paper clips, hairpins, bend the hook.
3. Attach the hook firmly to the fishing line.
4. Insert the tool inside the door.
5. Hook the glass from below.
6. Pull it up.

In case of failure, in order to close the window in the car, if the power window does not work, it is necessary to provide access to the mechanism.

Opening the door

The best way to close the window in your car if the power window is broken is to buy a repair kit and fix the problem yourself.

Opening the door

If spare parts are not available, proceed as follows:

1. Prepare a screwdriver and pliers.
2. Remove the door panel carefully.
3. Fold back the locking bar.
4. Unscrew the mounting bolt, remove the frame.
5. Raise the glass and secure it firmly with a support.

As a support, take any object of the desired size.

What can you do yourself to fix the problem

To close the window in the car if the power window does not work, determine the cause of the breakdown. In automatic lifting devices, the electrical and mechanical parts are to be checked.

Malfunctions in the electrical system of the lifting mechanism and methods for their elimination:

1. Using a tester or a 12V bulb, check the fuse for the electric lift. If it burned out, replace it.
2. Measure the voltage at the motor terminals. If there is no voltage, you need to test the wiring, relay, control unit. The current is supplied, but the motor does not work - a replacement will be required. Without special knowledge, such repairs will become a difficult task. Contact an auto electrician.
3. The button does not work without turning the ignition key. Perhaps the contacts are oxidized and need to be cleaned. If cleaning does not help, install a new button.
4. The village of the battery. This happens when the car is idle for a long time. Charge the battery, and if this is not possible, try to raise the glass by pressing the button frequently. You can unscrew the door panel and start the lift motor using a battery from another device. For example, a battery from a screwdriver.

Electric lift fuse

In a situation where the auto electrician is normal, but it is impossible to close the window in the car, then if the window regulator is broken, the reason is in the mechanics.

In a mechanical system, there may be such problems:

See also: Additional heater in the car: what is it, why is it needed, the device, how it works

1. The parts are jammed by a foreign object. Remove the door panel, pull it out.
2. There is noise when the button is pressed. A gear or bearing has broken in the gearbox, disassemble the device, change parts.
3. The cable burst or flew off the grooves. Unscrew the panel on the door, replace or reinstall the cable.

In older cars with mechanical lifts, there are such problems:

1. Turning the handle does not raise the glass. The reason is that the splines are worn out, the roller does not turn. Install a new handle with metal slots.
2. The device does not close the window - the gearbox and cable are worn out. Individual parts are not sold, it is better to change the lift assembly.

To prevent malfunctions, mechanical components and parts of closing systems must be periodically lubricated.

How to raise the glass if the power window does not work. Power window motor replacement