Heated windshield Nissan Qashqai j11
Control panel and controls
Turn the switch lever clockwise to
turn on the intermittent operation of the rear window wiper.
To stop the rear wiper, turn
handle switch to the OFF position.
Push the lever forward to start the washing machine
hold it until the rear window
the correct amount of fluid has been dispensed automatic purifier
Chesky will make a few strokes with brushes.
Removing glass drops (for some options
vehicle performance)
The vacuum cleaner will move the brushes after 3 seconds
after turning off the washing machine. This is done in order to
eliminate drops of liquid on the windshield.
This mode can be disabled. For additional
For more information, see "Displaying vehicle information-
later in this chapter.
Automatic activation while driving
reverse (for some options
vehicle performance)
If the wiper switch is on
intermittent working position or in position
AUTO (for some car modifications), in
constant working position at low or high speed
ste, then when reverse gear is engaged
rear window cleaner.
This mode can be disabled. For additional
For more information, see "Displaying vehicle information-
later in this chapter.
the switch is in the ON position. As a result, you can
personal injury or damage to the purifier.
At negative room temperature
liquid supplied to the rear window from the washer nozzles
cooler, it may freeze and impair visibility. Before use
when using the washing machine, it is recommended to heat the backrest
glass by turning on the electric heater.
Do not let the washing machine run continuously for a long time
Do not turn on the washing machine if not
liquid or if it is frozen.
Windshield wipers and rear window washers operate only
with the ignition on.
See also: New car for 300 thousand rubles
Removing glass drops (for some options, use
refilling the car)
The vacuum cleaner will move the brushes after 3 seconds
after turning off the washing machine. This is done in order to
eliminate drops of liquid on the windshield.
Rain sensor (for some variants
vehicle performance)
If the selector lever is in the AUTO position
, then the automatic wiper sensor,
located at the top of the windshield in front of the mirror
rear view stool, can automatically turn on cleaning
bodies and adjust the speed of its work depending on
precipitation intensity and vehicle speed.
You can adjust the sensitivity of the rain sensor,
turn the dial forward
A (less sensitive-
ness) or back
B (high sensitivity).
Be sure to disable automatic mode
cleaning bots before entering the car
sink.
If you leave the switch lever in the AUTO position,
this will not damage the rain sensor system, although it may
possible unexpected operation of the vacuum cleaner.
If the selector lever remains in the AUTO position,
then the purifier may suddenly turn on if the area
rain sensor configuration left fingerprints,
has dirt, oil film or insects.
The wiper may also turn on if the sensor
exhaust fumes or moisture.
Do not touch or cover the surface of the windshield
glass at the location of the rain sensor. Purifier
may suddenly turn on if the switch
in the AUTO position and the ignition key
If your windshield heating does not work, you can use the simple temporary solutions found by the forum members during the discussion and operation of the car.
For button start engine configurations:
Option 1. We start the car, let the engine run a little, then “gas” a little on the spot, slightly increasing the speed, then turn on the heating.
Option 2: Press the start button without brake to turn on the ignition first, then press the start button with brake to start the car, then turn on the heating.
For complete sets without a button (factory with a key):
Option 1. We start the car, let the engine run a little, then “gas” a little on the spot, slightly increasing the speed, then turn on the heating.
Option 2. We start the car without pressing the brake, then turn on the heating.
The manufacturer acknowledged and corrected the error. It is located in the engine control module (ECM) software. The solution to the problem is to update the ECM firmware:
https://qashqairus.ru/index.php?threads/229&page=92/post-73489&viewfull=1#post73489
There is no revocation campaign for this issue, the issue is resolved when the customer contacts the issue.
PS: Since the touch check of heating is rather ambiguous, there is an easy and quick way to check the effectiveness of heating: a magnetic compass (regular or electronic on a smartphone). The compass must be placed in the center of the front panel; when the heating is turned on / off, the compass needle should deviate by
20. 40 degrees, because the continuous current through the vertical heating filaments creates a magnetic field that affects the compass readings.
An increase in engine speed when the heating is turned on / off is not a guarantee of the latter's performance.
Show. Heating and air conditioning system. Audio system
This symbol means that the ventilation grill
how closed. By moving the side slider on this
position will close the vent
Grid
Adjust the airflow from the vents,
by moving the central slider (up/down, left/to
right) until it provides the desired position
ventilation holes.
When a strong beam of light enters the camera lens
the display of items on the monitor may look strange
kim It's not a mistake.
The screen may flicker under fluorescent lighting.
This is not a malfunction.
The color of objects on the Around View Monitor may
different from reality it is not recognized
communication failure
The image of items on the monitor may not
clear, and its color may differ from the actual
at low light levels. Is not
fault signal
Sharpness of the image in the bird's-eye view mode
whose flight” may vary.
If dirt gets into the rear view camera lens,
rain or snow the image of objects on the monitor
360° view may be fuzzy clear volume
lens.
Do not use the camera to clean the lens -
alcohol, gasoline and other solvents will cause
lens cap opacity and distorted color
Transmission. To clean the camera lens, use
soft cloth dampened with a neutral detergent solution
detergent, and then wipe the lens with a soft dry cloth
the cloth.
Be careful not to damage the lens in any way.
measurements, as this will affect the image on the screen
monitor.
Do not apply polish to the camera lens.
If polish or wax gets on the camera lens
wipe the lens with a clean soft cloth,
moistened with a neutral detergent solution.