P0627 Fuel Pump Control Circuit A / Open

OBD-II Trouble Code - P0627 - Technical Description

P0627 - Fuel pump control circuit A / open

What does trouble code P0627 mean?

This is a Generic Powertrain Diagnostic Trouble Code (DTC) applicable to many OBD-II vehicles (1996 and newer). This may include, but is not limited to, Ford, Dodge, Toyota, Chrysler, Jeep, Ram, Chevrolet, Nissan, Mitsubishi, Mercedes, etc. Despite the general nature, the exact repair steps may vary depending on the year of manufacture. brands, models and transmissions. configuration.

If a P0627 code appears, it means there is a problem in the "A" fuel pump control circuit. This is usually caused by damaged wires / connectors inside the circuit or CAN bus. The powertrain control module (PCM) or engine control module (ECM) usually identifies this code, however other accessory modules can also call this particular code, for example:

• Alternative fuel control module
• Fuel injection control module
• Turbocharger control module

Depending on the make and model of the vehicle, it may take several driving cycles before it can activate this code, or it may be an immediate response as soon as the ECM recognizes a malfunction.

The fuel pump is an integral part of the vehicle's overall handling. After all, without a fuel pump, there would be no fuel supply to the engine. The control circuit, generally speaking, is responsible for turning the pump on and off depending on the needs of the operator. An open in the indicated circuit can also activate the P0627 code, so keep this in mind before proceeding with any kind of diagnosis.

Typical fuel pump:

Relevant fuel pump A control circuit codes include:

• P0627 Fuel pump control circuit "A" / open
• P0628 Low rate of the fuel pump control circuit "A"
• P0629 High signal in the fuel pump control circuit "A"
• P062A Fuel pump "A" Control circuit range / performance

What is the severity of this DTC?

This particular DTC is a moderately serious problem for your vehicle. You can still use your vehicle despite the problem. However, it is strongly advised to avoid this because you can risk intermittent fuel delivery to the engine, and an unstable or fluctuating fuel mixture can definitely cause serious engine damage.

What are some of the symptoms of the code?

The only commonly observed symptoms are a stored code P0627 and a check engine light coming on. In many cases, the Check Engine light is off and the stored code is displayed as "pending" in the PCM.

Symptoms of a P0627 trouble code may include:

• Check engine light is on.
• Engine won't start
• Ignition misfire / engine stall
• Engine starts but dies
• Reduced fuel economy
• Engine turns normally but will not start
• Engine stalls when operating temperature is reached

Note. It is possible that the problem is indeed not resolved, even if the check engine light does not come on immediately. Always make sure your vehicle has gone through several driving cycles. those. drive the car for a week, if the CEL (Check Engine Light) does not come on all the way, the problem is most likely solved.

What are some of the common causes for the code?

Reasons for this code may include:

• Problems with the fuel pump itself
• Broken or damaged ground wire in the control module of the device.
• Loose ground jumper on control module
• Open, short or corroded wiring in the CAN bus
• Loose harnesses and wires causing abrasion or open circuit
• High circuit resistance (e.g. melted / corroded connectors, internal corrosion of wires)
• Faulty fuel pump relay
• Electrical components in the CAN bus harness, such as wiring or connectors that are corroded, open, or shorted.
• Loose control module ground wire
• Break of a wire of weight of the block of management
• Faulty CAN bus
• Bad electrical connection in the fuel pump circuit.
• Open or short in fuel pump wiring harness

What are some steps to troubleshoot the P0627?

The first thing I recommend that you do is review the vehicle-specific Technical Service Bulletins (TSBs) by year, model, and powertrain. In some cases, this can save you a lot of time in the long run by pointing you in the right direction.

Basic step 1

You should always immediately scan and test each module with an OBD-II scanner to get a good idea of ​​the general electrical condition of your vehicle and its modules. You should also always do a visual inspection of the connectors and wiring if there is anything clearly damaged in which case it should be repaired or replaced. They are often located under the vehicle next to the fuel tank. They are susceptible to road debris and elements, so pay close attention to their health.

Basic step 2

When working on any component with its own module (such as a fuel pump module, etc.), check the ground circuits. This can be done by using a separate battery ground. This is sometimes easy to do with an auxiliary ground cable. If your problem is resolved with an auxiliary ground connected, but then returns when an OEM ground is used, this would indicate that your ground cable is causing the problem and needs to be repaired or replaced. Always carefully check the ground connection for corrosion. terminals, contacts, etc., which can cause resistance in the circuit. A good sign of excessive corrosion is a green ring around the connector attached to the positive battery post. If present, remove the terminal and clean all contact points, connector surface and terminal block / stud.

Basic step 3

Given that an open circuit could be the cause of the P0627 code, you should identify the circuit using the circuit diagram in your service manual. Once identified, you can trace the individual fuel pump control wire A separately to see if there are any obvious breaks in the wire. Repair as needed by soldering the wire (which I recommend) or using heat shrink butt connectors to isolate it from the elements. Using a multimeter, you can measure the resistance between the connectors in a circuit to pinpoint the location of the short / open circuit. It is highly recommended to use a power probe tool here if there is a fault somewhere within the entire circuit.

I hope this article has helped point you in the right direction for diagnosing a fuel pump control circuit DTC problem. This article is for informational purposes only and specific technical data and service bulletins for your vehicle should always take priority.

How does a mechanic diagnose a P0627 code?

The first step to diagnosing a DTC is to use an OBD-II scanner to check the code. Once the mechanic has used the scanner to locate the P0627 code, they will begin the diagnostic procedure by visually inspecting all wiring and other electrical components associated with the CAN bus and fuel pump. Any shorted, exposed or corroded items will be repaired or replaced.

The PCM should then be cleared and the system retested. If the code reappears, the mechanic can move on to other repair options. A specialized scanner, such as an Autohex or a dedicated CAN scanner, may be required to locate a specific fault area in most of the electrical components that may be involved.

Common Mistakes When Diagnosing Code P0627

When a code P0627 is stored, it is likely that several other codes will be stored due to a communication failure between modules. These codes are often repaired by mistake when the fuel pump or related problems are at fault. If a code P0627 is stored along with others, it is important to make sure that this code is not at fault before troubleshooting other problems.

What repairs can fix code P0627?

To resolve the cause of the P0627 code, a mechanic can perform any of the following repairs:

• Replace faulty fuel pump
• Replace the faulty fuel pump relay/
• Replace or repair any electrical components in the CAN bus harness such as wiring or connectors that are corroded, open, or shorted.
• Adjust loose control module ground wire.
• Replace broken control module ground wire.
• Replace failed CAN bus
• Repair poor electrical contact in the fuel pump circuit.
• Replace or repair open or shorted fuel pump harness.

Additional comments to consider regarding code P0627

When performing diagnostic tests or repairs related to this code, the mechanic should always clear the code and retest the system after each repair attempt. Without this step, the mechanic may not know which repair solved the problem and may waste time and money on repairs that were not needed.

P0627 ✅ SYMPTOMS AND CORRECT SOLUTION ✅ - OBD2 Fault Code

Need more help with the P0627 code?

If you still need help with DTC P0627, post a question in the comments below this article.

NOTE. This information is provided for informational purposes only. It is not intended to be used as a repair recommendation and we are not responsible for any action you take on any vehicle. All information on this site is protected by copyright.