U011C Lost Communication With Rocker Arm Control Module B

U011C Lost Communication With Rocker Arm Control Module B

OBD-II DTC Datasheet

Lost Communication With Rocker Arm Control Module B

What does this mean?

This is a generic communications system diagnostic trouble code that applies to most makes and models of OBD-II vehicles.

This code means that Rocker Arm Control Module B (RACM-B) and other control modules on the vehicle are not communicating with each other. The circuitry most commonly used for communication is known as Controller Area Bus communication, or simply the CAN bus.

Modules communicate with each other over a network, just like the network you have at home or work. Car manufacturers use several networked systems. Prior to 2004, the most common (non-exhaustive) inter-module communication systems were the serial communication interface, or SCI; SAE J1850 or PCI bus; and Chrysler Collision Detection, or CCD. The most common system used after 2004 is known as Controller Area Network communication, or simply the CAN bus (also used until 2004 on a small segment of vehicles). Without this CAN bus, control modules cannot communicate and your scan tool may or may not receive information from the vehicle, depending on which circuit is affected.

Rocker Arm Control Module B (RACM-B) is usually located under the bonnet, typically on the engine valve covers. May also be part of PCM. It receives input from various sensors, some of which are directly connected to it, and most are sent over a bus communication system from the powertrain control module (PCM). These inputs allow the module to inform the PCM of the rocker arm position for each cylinder. Allows the PCM to control the variable valve timing system. More commonly used in multi-valve per cylinder engines.

Troubleshooting steps may vary depending on the manufacturer, the type of communication system, the number of wires, and the colors of the wires in the communication system.

Code severity and symptoms

The severity in this case is not serious because PCM has a backup strategy in case it loses communication with RACM-B.

Symptoms of a U011C code may include:

• Malfunction Indicator Light (MIL) is on
• May exhibit poor fuel economy / performance
• Engine may skip ignition, only possible at idle or at freeway speeds

reasons

Usually the reason for installing this code is:

• Open on CAN bus + or - circuit
• Short to ground or ground in any CAN bus circuit
• No power or ground to RACM-B
• Rarely - the control module is faulty

Diagnostic and repair procedures

A good place to start with ALL electrical diagnostics is to check the Technical Service Bulletins (TSB) for your vehicle. The problem you are facing may be known to others in the field. A known fix may have been released by the manufacturer and can save you time and money during diagnostics.

It is assumed that a code reader is available to you at this point, as you may have been able to access the codes up until now. See if there were any other DTCs related to bus communication or battery / ignition. If so, you should diagnose them first, as misdiagnosis is known to occur if you diagnose the U011C code before any of the underlying codes are thoroughly diagnosed and corrected.

If the only code you get from other modules is U011C, try accessing RACM-B. If you can access codes from RACM-B, then code U011C is either intermittent or memory code. If the RACM-B cannot be accessed, then the code U011C set by other modules is active and the problem already exists.

The most common failure is a circuit failure that results in a loss of power or ground to the rocker control module b.

Check all fuses supplying the RACM-B module on this vehicle. Check all the grounds for RACM-B. Locate grounding attachment points on the vehicle and make sure these connections are clean and secure. If necessary, remove them, take a small wire bristle brush and baking soda / water solution and clean each one, both the connector and the place where it connects.

If any repairs have been made, clear the diagnostic trouble codes from any modules that set the code in memory and see if you can now communicate with the RACM-B module. If communication with the RACM-B recovers, the problem is most likely a fuse / connection issue.

If the code returns or communication with the module still cannot be established, look for the CAN bus communication connections on your vehicle, primarily the RACM-B connector, which is usually found under the hood, usually on the engine valve covers. can also be part of the RMB. Disconnect the negative battery cable before disconnecting the connector from the RACM-B. Once detected, visually inspect the connectors and wiring. Look for scratches, scuffs, exposed wires, burn marks, or molten plastic.

Disconnect the connectors and carefully inspect the terminals (metal parts) inside the connectors. See if they look burnt or have a green tint indicating corrosion. If you need to clean the terminals, use an electrical contact cleaner and a plastic bristle brush. Allow to dry and apply electrical grease where the terminals touch.

Perform these few voltage checks before plugging the connectors back into the RACM-B. You will need access to a digital volt-ohmmeter (DVOM). Make sure you have power and ground at the RACM-B. Access the wiring diagram and determine where the main power and ground supplies go into the RACM-B. Reconnect the battery before proceeding with the RACM-B disconnected. Connect the red wire of your voltmeter to each B + (battery voltage) power source going into the RACM-B connector, and the black wire of your voltmeter to a good ground (if unsure, the negative pole of the battery always works). You should see the battery voltage reading. Make sure you have a good reason. Connect the red wire from the voltmeter to battery positive (B +) and the black wire to each ground. Once again, you should see the battery voltage every time you plug it in. If not, troubleshoot the power or ground circuit.

Then check the two communication circuits. Locate CAN C+ (or HSCAN+) and CAN C- (or HSCAN - circuit). With the black wire of the voltmeter connected to a good ground, connect the red wire to CAN C+. With the key on and engine off, you should see about 2.6 volts with little fluctuation. Then connect the red wire of the voltmeter to the CAN C- circuit. You should see about 2.4 volts with little fluctuation. Other manufacturers show CAN C- at about 5V and an oscillating key with the engine off. Check your manufacturer's specifications.

If all tests pass and communication is still not possible, or you were unable to clear DTC U011C, the only thing that can be done is to seek help from a trained automotive diagnostician as this will indicate a RACM-B failure. . Most of these RACM-Bs must be programmed or calibrated to fit properly on the vehicle.

Related DTC discussions

• There are currently no related topics in our forums. Post a new topic on the forum now.

Need more help with code U011C?

If you still need help with DTC U011C, post a question in the comments below this article.

NOTE. This information is provided for informational purposes only. It is not intended to be used as a repair recommendation and we are not responsible for any action you take on any vehicle. All information on this site is protected by copyright.