Replacing the bearing of the front and rear hub on Renault Logan

You should not undertake to replace the wheel bearing with Renault Logan I and II generations if there is no special tool or experience in car repair, as improper installation of a new spare part can damage the inner surface of the steering knuckle or brake drum.

The characteristic noise from the ailerons at high speed, knocking, steering play when the steering wheel is rocked left-right, up and down are clear signs of wear on the front or rear wheel bearing on Renault Logan I and II. This article will tell you how to choose a replacement part and install it yourself.

Front hub

The Renault Logan front suspension of the first and second generation uses double-row ball bearings. There are two types: for cars equipped with anti-lock brakes and without it. In the first case, the magnetic poles are located on one side of the bearing. As the wheel rotates through them and the adjusting ring, the wheel speed sensor collects the information needed to operate the ABS.

Outside diameter, mm	Inner diameter, mm	Height, mm
72	37	37

Life time

Under normal operating conditions and with a closed hub nut with a protective cap, the service life of original spare parts is 100-110 thousand kilometers.

Codes of original spare parts

In the original spare parts catalog, wheel bearings are identified by the following numbers:

• For vehicles with ABS:

Supplier code	Note	average price
6001547686	Vehicles manufactured before March 2007. Contains 44 magnetic poles.	3389
7701207677	Vehicles manufactured after March 2007. Contains 48 magnetic poles.	2191

• For vehicles without ABS:

Supplier code	average price
6001547696	2319

The number of magnetic poles affects the accuracy of the readings collected by the anti-lock braking system while driving and, as a result, the operation of the engine and brake system.

Analogues

There are options for installing spare parts that are identical in resource to the original ones and at a lower price, SNR products:

• For vehicles with ABS:
  • collected before March 2007 - 41371.R00;
  • collected after March 2007 - XGB.41140.R00.
• For vehicles without ABS - GB.40706.R00.

The products of this company are installed on Renault Logan from the assembly line.

Other replacement options with prices are shown in the table.

For vehicles with ABS manufactured before March 2007:

Creator	Supplier code	average price
ABS	201127	2232
ENDIKAR	ANR15580	1392
ASSAM SA	30454	1437
AUTOLOGIST	RS1290	3545
AUTOMEGA DELLO	110101310	1038
AUTOMOBILE FRANCE	ABR5580	1638
BTA	H1R026BTA	1922 g
WORK	CR075	1256
Customer Experience	CX971	1541
DENKERMANN	W413279	1600
ESPRA	ES737686	1362
pedik	713630990	3861
FEBRUARY	DAK37720037MKIT	1618
Phoebe	26887	3148
FRANCESCAR	FCR210241	1650
Gallant	GLBE110	905
GSP	GK6561	2029
IBERIS	IB4139	1310
KLAXCAR FRANCE	22010Z	1500
KRAUF	WBZ5516KR	1063
Crowns	K151196	899
LYNX	WB1289	2196
MANEUVER	MR8018235	729
MAPCO	26150	1572
MAIL	16146500007	2693
MUG	REWB11469	2126
NDM	1000020	750
NK	753929	1538
PNA	NP51103514	1043
NTY	KLPRE029	1164
OPTIMUM	701837	2016
SAMPLE	PBK6561	1277
IFP	PW37720437CSM88	2092
PILENGA	PWP6561	1048
FOUR BRAKES	QF00U00001	1098
RUEVIL	5584	4434
SPEC	GF015584	1084
SCF	VKBA6561	2398
STELLOX	4328402SX	1021
TOPRAN	700546755	1527
TORQUE	PLP101	1566
TSN	3481	1089
ZECKERT	RL1258	1422

For vehicles with ABS manufactured since March 2007:

Creator	Supplier code	average price
ABS	200425	2797
AKDELCO	19381516	3454
Amd	AMBER49	1376
ENDIKAR	ANR15575	1630
ASSAM SA	30925	1460
Ashika	4411042	1284
ASVA	DACM37720037	2416
AUTOMOBILE FRANCE	ABR5575	2920
BTA	H1R023BTA	1965 g
WORK	CR076	1488
Customer Experience	CX701	1757 g
DENKERMANN	W413272	1656
Doda	1060200280	1080
ESPRA	ES137677	1166
pedik	713630840	4563
FEBRUARY	DAK37720037MKIT	1618
Phoebe	24315	3645
WHALE FIN	HB701	1103
FLENOR	FR799209	1050
FRANCESCAR	FCR210242	805
Gallant	GLBE110	905
GSP	GK3637	1971 g
IBERIS	IB4143	1545
ILYIN	IJ131014	2060
SPARE PARTS FOR JAPAN	QC11042	1609
JD	JEW0115	1233
JAPE GROUP	4341301410	1803 g
KLAXCAR FRANCE	22010Z	1500
SHEEP	K0Y08088	2016
KRAMME	KW36175	1045
Crowns	K151247	1112
LGR	LGR4711	991
LYNX	WB1202	1926 g
MAGNETI MARELLI	361111183126	4173
MANEUVER	MR8018235	729
MAPCO	26100	1009
MASTER SPORT	3637 SETS	2483
MAIL	16146500011	2759
MUG	REWB11451	2080
SPARE PARTS	N4701045	1484
NK	753926	1435
PNA	NP51103522	673
NPS	NSP077701207677	800
OPTIMUM	702312	1515
SAMPLE	PBK3991	1605
POLKAR	CX701	2100
FOUR BRAKES	QF00U00001	1098
Renault	7701207677	3381
HE SAT	ST40210AX000	1100
SPEC	GR000431	819
SCF	VKBA1439	1670
SCF	VKBA3991	2103
SCF	VKBA1403	2673
STAR	S100181	962
STELLOX	4328217SX	1104
TOPRAN	700638755	1553
TRIXET	D1003 NO	1080
ZECKERT	RL1282	1270
ZZVF	ZVPH038	1269

For vehicles without ABS

Creator	Supplier code	average price
ABS	200815	1928 g
Amd	AMBER48	1221
AMIVA	6241081	810
ENDIKAR	ANR15516	1397
ASSAM SA	30454	1437
HOW IN	ASINBER248	1087
AUTOMOBILE FRANCE	April 1516	958
BAPTERO	BTLB406	906
BURDEN	26100	1239
WORK	CR016ZZ	861
Customer Experience	CX101	1155
DENKERMANN	W413235	1935 g
Doda	1060200279	886
REPAIR	1623960780	1422
pedik	713630030	1680
FEBRUARY	DAC37720037KIT	1024
Phoebe	5528	1123
WHALE FIN	HB702	924
FLENOR	FR799209	1050
FRANCESCAR	FKR210240	1181
Gallant	GLBE19	736
GMB	GH037020	1030
GSP	GK3596	1204
DUKE GERMANY	5779 peso	791
IBERIS	IB4208	1011
ILYIN	IJ131009	1290
SPARE PARTS FOR JAPAN	QC11001	1413
KLAXCAR FRANCE	22040Z	897
SHEEP	K0Y08088	2016
KRAUF	WBZ5516KR	1063
Crowns	K151193	825
LGR	LGR4721	672
LYNX	WB1186	1385
MANEUVER	MR8018127	768
MAPCO	26100	1009
MAIL	16141464049	1725
MUG	REWB11451	2080
NK	753910	976
NTY	KLPNS064	1090
OPTIMUM	700310	1366
SAMPLE	PBK3596	1065
IFP	PW37720037CS	1106
PILENGA	PWP3596	744
QML	WB1010	550
QUARTZ	QZ1547696	985
QUINTON HAZELL	4341300519	1754 g
RUEVIL	5516	2306
HE SAT	ST40210AX000	1100
SPEC	GF015516	1140
SCF	VKBA3596	1800
star line	L003596	1406
STYLE	60905528	1120
TOPRAN	700178755	1188
TSN	3424	579
ZECKERT	RL1139	876

Self replacement

Required Tools

• end heads 16, 30mm;
• necklace 0,5-1 m long;
• anti-reverse stops;
• Jack;
• car mount;
• balloon wrench;
• screwdriver;
• assembly sheet;
• keys for 13, 16, 18 mm, Torx T30, T40;
• wire or lace;
• a hammer;
• metal bar;
• screw;
• bit;
• pliers for retaining rings;
• cup shooter

Procedure

To replace the front wheel bearing you need:

1. Place the vehicle on a level surface, block the rear wheels with the parking brake and place wedges under them.
2. Loosen the front wheel mounting bolts.
3. Using a screwdriver, remove the cap covering the hub nut.
4. Loosen the hub nut with a 30mm wrench. If the wheel is slipping, it can be blocked by depressing the brake pedal.
5. Raise the car with a jack, install a stand and remove the wheel.
6. For vehicles with ABS. Remove the wheel speed sensor attached to the steering knuckle:
   1. remove the cover;
   2. disconnect the sensor wires from the wiring block attached to the stringer by pressing the plastic clips;
   3. remove the cable from the brackets on the stringer and suspension strut;
   4. press the plastic tabs on the back of the brake disc and pull out the sensor.
7. Remove the brake mechanism:
   1. tighten the brake pads with a mounting spatula;
   2. Press disc brake pads
   3. with an 18 wrench, unscrew the two bolts securing the guide pad to the steering knuckle;
   4. From the inside, unscrew the two screws of the caliper brackets 18
   5. remove the caliper bracket from the guide shoe and hang it on the front suspension spring with a wire or rope;
   6. remove the brake disc by unscrewing the two screws with a Torx T40 key;
   7. remove the brake shield by unscrewing the three screws with a Torx T30 wrench.
8. Detach the tie rod end:
   1. unscrew the nut with a 16 wrench, preventing the bolt from turning with a Torx T30 wrench;
   2. press the end of the steering rod with a mounting spatula.
9. Detach the ball joint:
   1. unscrew the socket heads of the 16 bolt at the bottom of the steering knuckle and remove it;
   2. push the terminal connection with a mounting spatula;
   3. move the control lever down, pressing it with the mounting sheet, one end resting on the steering knuckle.
10. Disconnect the steering knuckle from the damper by unscrewing the two bolts with 18 wrenches and tapping them with a hammer and a metal rod.
11. Clamp the steering knuckle in a vise with the hub down.
12. Press the hub with a 30mm head or a piece of pipe of a suitable diameter.
13. Use a screwdriver to remove the washer covering the bearing seal.
14. Clamp the hub in a vise and use a chisel to knock out the inner race of the bearing.
15. Pull out the retaining ring with pliers.
16. Press the outer ring of the part to remove it from the hub.
17. For vehicles with ABS. Position the adjusting ring with the centering lugs inside the stud. The holes in it should face towards the mounting location of the wheel speed sensor.
18. Push the new part into the bucket. If the machine is equipped with ABS, the part must face the mounting ring with the dark shield.
19. Install the circlip and press the hub into the bearing.
20. New item in place
21. Install the rest of the parts in reverse order.

Rear hub

The Renault Logan rear hub bearing has two rows of rollers. The product is of two types. difference in physical size.

dimensions

For vehicles built before 2013

Outside diameter, mm	Inner diameter, mm	Length, mm
52	25	37

For vehicles built since 2013

Outside diameter, mm	Inner diameter, mm	Length, mm
55	25	43

There are no structural differences associated with the presence of an anti-lock braking system.

Life time

The original rear wheel bearings are rated for over 100 kilometers on average quality roads.

Articles of original spare parts

In the original spare parts catalog, rear wheel bearings for Renault Logan are indicated by the following codes:

Supplier code	Note	average price
77 01 205 812	For cars manufactured before 2013	1824 g
77 01 205 596 77 01 210 004	For assembly vehicles from 2013 (inclusive)	2496 3795

Analogues

Genuine parts can be obtained cheaper by purchasing SNR products:

• for cars manufactured before 2013 - FC 40570 S06;
• for cars produced since 2013 - FC 41795 S01.

Other replacement options with prices are shown in the table.

For cars built before 2013

Creator	Supplier code	average price
ABS	200004	1641
ASSAM SA	30450	820
AUTOMEGA DELLO	110108710	1553
BAPTERO	BTLB406	906
BRACKNER	BK26202	636
BTA	H2R002BTA	1294
AUTOMOTIVE BEARINGS	GHK045L028	518
WORK	CR025	567
Customer Experience	CX597	1099
DENKERMANN	W413092	2006 g
Doda	1060200284	825
ERSUS	ES7701205812	687
ESPRA	ES138504	847
REPAIR	1623954980	1341
pedik	713630300	1501
FEBRUARY	DAC25520037KIT	879
Phoebe	5538	1112
FLENOR	FR791201	1220
FRANCESCAR	FKR210243	1487
Gallant	GLBE111	628
GMB	GH025030	960
IBERIS	IB4256	901
DPI	303030	1503
JD	Jew0098	585
KLAXCAR FRANCE	22002Z	1318
LYNX	WB1173	1140
MAGNETI MARELLI	361111181790	2246
MAPCO	26102	921
MAIL	16146500001	1845 g
MUG	REWB11479	1692
NDM	1000053	726
SPARE PARTS	N4711064	1030
PNA	NP51103522	673
NTY	KLTNS071	1079
OPTIMUM	702312S	1122
PEX	160660	932
PILENGA	PWP3525	645
BENEFIT	25013525	625
BENEFIT	25010869	691
QML	WB0516	1116
HE SAT	ST7701205812	928
SPEC	GR000431	819
SCF	VKBA3525	1429
STELLOX	4328020SX	817
STYLE	60905538	1092
TORQUE	TRK0592	690
TORQUE	DAK25520037	978
TRIALS	CS908	1008
TRIXET	D1004 NO	1394
VENDERV	VEPK004	585
ZECKERT	RL1135	866

For cars built from 2013

Creator	Supplier code	average price
ABS	200010	1466
ASSAM SA	70820	1177
AUTOMOBILE FRANCE	April 1558	801
BTA	H2R016BTA	1574
WORK	CR038	1144
Customer Experience	CX102	1028
pedik	713630050	3222
FEBRUARY	DAC25550043KIT	1442
Phoebe	5526	1085
FLENOR	FR790296	2285
Gallant	GLBE114	762
GMB	GH0048R5	1004
GSP	GK0976	1088
ILYIN	IJ231001	1953 g
DPI	303027	1684
JD	Jew0079	690
KLAXCAR FRANCE	22007Z	1235
MAPCO	26124	1341
MAIL	16146500008	2294
MUG	REWB11451	2080
NK	753918	1479
NTY	KLTRE016	903
OPTIMUM	702426	2072
SAMPLE	PBK6658	1177
BENEFIT	25010976	884
SHIGER	SC293	500
SPEC	GF000564	999
SCF	VKBA3495	3249
SCF	VKBA6658	2118
SCF	VKBA976	2082
star line	L000976	1350
STARMANN	RS7307	1413
STELLOX	4328037SX	765
STYLE	60919897	1934 g

Self replacement

Required Tools

• socket head 30 mm;
• necklace 0,5-1 m long;
• anti-reverse stops;
• Jack;
• car mount;
• balloon wrench;
• screwdriver;
• screw;
• pliers for retaining rings;
• cup shooter

Procedure

To replace a rear wheel bearing:

1. Prepare the vehicle:
   1. engage first gear or shift the automatic transmission to P mode,
   2. put wedges under the front wheels,
   3. loosen wheel bolts
   4. release the handbrake
   5. Remove the protective cap from the hub nut.
2. Loosen the hub nut with a 30mm wrench.
3. When the car is lowered, loosen the hub nut
4. Raise the car on a jack and place a stand under it.
5. Remove the wheel.
6. Remove the brake drum. If this is not possible, screw the wheel with the convex side of the disk to the drum and, pressing the wheel hard to the left and right, remove the part. Drum removed
7. Remove the retaining ring with pliers from the groove in the brake drum.
8. While holding the brake drum in a vise, remove the bearing with a puller. Removing the old bearing
9. Clean the installation site of the new part from dirt and lubricate with engine oil. old bearing
10. Press in the new part using the outer ring of the old part as a driver. A new part has been installed. Be careful not to damage the sensor trim ring.
11. Install the removed parts in their original places.